{"product_id":"70mm-jr-servo-y-cable-splitter","title":"70mm JR-Style Servo Y Cable - 1 Male to 2 Female Splitter","description":"\u003cdiv class=\"nznpd\"\u003e\n\u003cdiv class=\"nznpd__lead\"\u003e\n\u003cp class=\"nznpd__intro\"\u003eA servo Y cable lets one receiver channel drive two servos at once. This one is only 70mm long and uses the JR colour code: brown negative, red positive and orange signal. The single end is a small servo-style plug that slides onto the receiver's header pins, and the two other ends are receptacles your servo plugs push into. It is the one to choose when both servos sit close to the receiver, so there is no loop of spare lead to tuck away. If your servos sit further apart, our \u003ca href=\"\/products\/150mm-futaba-servo-y-cable-splitter\"\u003e150mm Futaba-style Y cable\u003c\/a\u003e reaches about twice as far.\u003c\/p\u003e\n\u003cp class=\"nznpd__intro\"\u003eYou can use it to run a pair of aileron servos or twin boat rudders from one channel. It can also take power from a spare receiver port for small add-ons such as LED lights. Both servos get the same signal, so they always move the same way. If one needs to move the opposite way, turn it round in its mount, fit a servo reverser on that side, or put each servo on its own channel and mix them on the transmitter. The housings have no key tab, so JR, Spektrum and Hitec leads push straight in, and Futaba leads use the same pin order.\u003c\/p\u003e\n\u003c\/div\u003e\n\n\u003csection class=\"nznpd__block\"\u003e\n\u003ch3 class=\"nznpd__h\"\u003eSpecifications\u003c\/h3\u003e\n\u003cdiv class=\"nznpd__specs\"\u003e\n\u003cdiv class=\"nznpd__spec\"\u003e\n\u003cspan\u003eType\u003c\/span\u003e\u003cstrong\u003ePassive servo Y cable, 1 to 2\u003c\/strong\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"nznpd__spec\"\u003e\n\u003cspan\u003eEnds\u003c\/span\u003e\u003cstrong\u003e1 servo-style plug, 2 receptacles\u003c\/strong\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"nznpd__spec\"\u003e\n\u003cspan\u003eConnector style\u003c\/span\u003e\u003cstrong\u003eJR-style, 3 positions, 2.54mm pitch\u003c\/strong\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"nznpd__spec\"\u003e\n\u003cspan\u003eWire colours\u003c\/span\u003e\u003cstrong\u003eBrown negative, red positive, orange signal\u003c\/strong\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"nznpd__spec\"\u003e\n\u003cspan\u003eLength\u003c\/span\u003e\u003cstrong\u003e70mm (2.8in) nominal\u003c\/strong\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"nznpd__spec\"\u003e\n\u003cspan\u003eCable\u003c\/span\u003e\u003cstrong\u003eTwo flat 3-core leads, no sleeve at the split\u003c\/strong\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"nznpd__spec\"\u003e\n\u003cspan\u003eFits\u003c\/span\u003e\u003cstrong\u003eJR, Spektrum, Hitec and Futaba servo leads\u003c\/strong\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"nznpd__spec\"\u003e\n\u003cspan\u003eSignal\u003c\/span\u003e\u003cstrong\u003eBoth servos share one signal, power and ground\u003c\/strong\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"nznpd__spec\"\u003e\n\u003cspan\u003eIn the box\u003c\/span\u003e\u003cstrong\u003e1 Y cable\u003c\/strong\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/section\u003e\n\n\u003csection class=\"nznpd__block\"\u003e\n\u003cdiv class=\"nznpd__qs\"\u003e\n\u003ch3\u003eWiring \u0026amp; getting started\u003c\/h3\u003e\n\u003cdetails class=\"nznpd__figbox\" open\u003e\u003csummary\u003eWiring diagram\u003cspan class=\"nznpd__codelang\"\u003eRC receiver\u003c\/span\u003e\u003c\/summary\u003e\u003cfigure class=\"nznpd__fig\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0664\/6127\/0112\/files\/CBL-SERVO-Y-JR-70-wiring-wide.png?v=1794170289\" target=\"_blank\" rel=\"noopener\"\u003e\u003cpicture\u003e\u003csource media=\"(min-width: 600px)\" srcset=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0664\/6127\/0112\/files\/CBL-SERVO-Y-JR-70-wiring-wide.png?v=1794170289\" width=\"920\" height=\"640\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0664\/6127\/0112\/files\/CBL-SERVO-Y-JR-70-wiring.png?v=1794170289\" alt=\"The Y cable plug on one receiver channel with the brown wire on negative, red on plus and orange on signal, and two servos plugged into its receptacles\" width=\"690\" height=\"680\" loading=\"lazy\"\u003e\u003c\/picture\u003e\u003c\/a\u003e\u003cfigcaption\u003eTap the drawing to open it full size.\u003c\/figcaption\u003e\u003c\/figure\u003e\u003c\/details\u003e\n\u003col class=\"nznpd__steps\"\u003e\n\u003cli\u003e\u003cdiv\u003e\n\u003cstrong\u003eSwitch everything off\u003c\/strong\u003e\u003cp\u003eUnplug the receiver battery or ESC before you plug anything in.\u003c\/p\u003e\n\u003c\/div\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cdiv\u003e\n\u003cstrong\u003ePlug the Y cable onto the receiver\u003c\/strong\u003e\u003cp\u003ePush the plug onto the channel you want with the brown wire on the negative pin. Receivers mark that pin with a minus sign, a battery symbol or GND. Orange then sits on the signal pin.\u003c\/p\u003e\n\u003c\/div\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cdiv\u003e\n\u003cstrong\u003ePlug in both servos\u003c\/strong\u003e\u003cp\u003ePush each servo plug fully into a receptacle, brown to brown. On Futaba-coloured leads, black goes where brown goes.\u003c\/p\u003e\n\u003c\/div\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cdiv\u003e\n\u003cstrong\u003eCheck it works\u003c\/strong\u003e\u003cp\u003ePower up and move the stick for that channel. Both servos should turn together in the same direction. If one moves the wrong way for your model, turn it round in its mount or fit a servo reverser to that side. If neither moves, the plug is on the wrong way round, so turn it over on the pins.\u003c\/p\u003e\n\u003c\/div\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cdiv\u003e\n\u003cstrong\u003eTie it down\u003c\/strong\u003e\u003cp\u003eHold the joints together with a cable tie or a wrap of tape so vibration can't pull a servo plug out.\u003c\/p\u003e\n\u003c\/div\u003e\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003c\/div\u003e\n\u003c\/section\u003e\n\u003c\/div\u003e\n","brand":"NZN Electronics","offers":[{"title":"Default Title","offer_id":67686016548960,"sku":"CBL-SERVO-Y-JR-70","price":3.99,"currency_code":"NZD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0664\/6127\/0112\/files\/01-servo-y-cable-70mm-jr-hero.png?v=1794171518","url":"https:\/\/www.nznelectronics.co.nz\/products\/70mm-jr-servo-y-cable-splitter","provider":"NZN Electronics","version":"1.0","type":"link"}