{"product_id":"kf301-2-pin-screw-terminal-block-5-08mm-pcb","title":"KF301 2-Pin Screw Terminal Block - 5mm Pitch, Fits 5.08mm PCB, Black","description":"\u003cdiv class=\"nznpd\"\u003e\n\u003cdiv class=\"nznpd__lead\"\u003e\n\u003cp class=\"nznpd__intro\"\u003eA KF301 is the standard two-pole screw terminal that solders into a circuit board and clamps a wire under a screw, so you can bring power, a motor, a sensor or a speaker lead onto a board without soldering the wire itself. This one is a 2-pin block at 5mm pitch that fits both 5.0mm and 5.08mm (0.2 inch) board footprints, black, with the wire opening on the front and the clamp screw on top.\u003c\/p\u003e\n\u003cp class=\"nznpd__intro\"\u003eIt takes stranded or solid wire from about 22 to 16 AWG (0.3 to 1.3mm²), which covers hook-up wire, small DC leads and speaker wire. Thicker 14 AWG wire may not go in. We would keep it to low-voltage DC and signal wiring, up to about 5A per terminal. It carries no approval markings, so it is not for 230V mains. For a 4-way block, use two. They are sold in lots of 5 or more.\u003c\/p\u003e\n\u003c\/div\u003e\n\n\u003csection class=\"nznpd__block\"\u003e\n\u003ch3 class=\"nznpd__h\"\u003eSpecifications\u003c\/h3\u003e\n\u003cdiv class=\"nznpd__specs\"\u003e\n\u003cdiv class=\"nznpd__spec\"\u003e\n\u003cspan\u003ePitch\u003c\/span\u003e\u003cstrong\u003e5mm, fits 5.0mm and 5.08mm (0.2in) footprints\u003c\/strong\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"nznpd__spec\"\u003e\n\u003cspan\u003ePoles\u003c\/span\u003e\u003cstrong\u003e2\u003c\/strong\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"nznpd__spec\"\u003e\n\u003cspan\u003eMounting\u003c\/span\u003e\u003cstrong\u003eThrough-hole PCB, solder pins\u003c\/strong\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"nznpd__spec\"\u003e\n\u003cspan\u003eWire range\u003c\/span\u003e\u003cstrong\u003e22 to 16 AWG (0.3 to 1.3mm²)\u003c\/strong\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"nznpd__spec\"\u003e\n\u003cspan\u003eWire entry\u003c\/span\u003e\u003cstrong\u003eFront opening, clamp screw on top\u003c\/strong\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"nznpd__spec\"\u003e\n\u003cspan\u003eColour\u003c\/span\u003e\u003cstrong\u003eBlack\u003c\/strong\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/section\u003e\n\n\u003csection class=\"nznpd__block\"\u003e\n\u003cdiv class=\"nznpd__qs\"\u003e\n\u003ch3\u003eWiring \u0026amp; getting started\u003c\/h3\u003e\n\u003col class=\"nznpd__steps\"\u003e\n\u003cli\u003e\u003cdiv\u003e\n\u003cstrong\u003eSolder it in first\u003c\/strong\u003e\u003cp\u003ePush the block into the board with the wire openings facing the way you want the wires to come from, and solder the two pins from underneath. Do this before you wire it, so the heat does not reach the clamp screws.\u003c\/p\u003e\n\u003c\/div\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cdiv\u003e\n\u003cstrong\u003eStrip and twist the wire\u003c\/strong\u003e\u003cp\u003eStrip about 6mm of insulation and twist stranded wire tightly so no strand strays.\u003c\/p\u003e\n\u003c\/div\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cdiv\u003e\n\u003cstrong\u003eClamp the wire\u003c\/strong\u003e\u003cp\u003eBack the screw off, push the bare wire into the front opening until it stops, and tighten the screw until the wire will not pull out. Stop when it is held. Forcing a small screw can strip the thread or crush the strands.\u003c\/p\u003e\n\u003c\/div\u003e\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003c\/div\u003e\n\u003c\/section\u003e\n\u003c\/div\u003e","brand":"NZN Electronics","offers":[{"title":"Default Title","offer_id":67798099492960,"sku":"CON-KF301-508-2P-BLK","price":0.59,"currency_code":"NZD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0664\/6127\/0112\/files\/CON-KF301-508-2P-BLK_1_hero.png?v=1794903052","url":"https:\/\/www.nznelectronics.co.nz\/products\/kf301-2-pin-screw-terminal-block-5-08mm-pcb","provider":"NZN Electronics","version":"1.0","type":"link"}