Active buzzer module, high level trigger version, top view on white

Active Buzzer Module for Arduino, High or Low Level Trigger, 3.3 to 5V

High level
$1.99 NZD
Save 5% at 3+
Skip to product information
SKU: MOD-BUZ-ACT-H

Active Buzzer Module for Arduino, High or Low Level Trigger, 3.3 to 5V

$1.99 NZD
Trigger
Availability:
Order before 7:30am (12pm weekends) for same-day dispatch Dispatch 7 days a week, excluding public holidays

NZ Post: 1-2 days urban · 2-4 days rural

Shipping from $5.99 urban / $9.99 rural, or free pick-up in Te Awamutu.

Buy more, pay less Prices shown are per unit. Add enough of this item and the lower rate applies on its own at checkout. There is no code to enter and you do not need to buy a pack. Choosing a tier here just sets the quantity for you. Larger quantities go out in the same bag, so packing, handling and postage cost us less per unit. We pass that saving straight on to you, so you can buy more for less.

Easy 30-day returns · 12-month warranty

Add these too
Add $50.00 for Free Urban delivery ($88.00 for Rural)
Urban $50 Rural $88

A small beeper board for Arduino, ESP32 and Raspberry Pi Pico projects. Set one pin and it beeps at a single fixed tone, so it suits alarms, timers, button clicks and error warnings with nothing more than digitalWrite. A transistor on the board does the switching, so your pin only supplies a few milliamps.

Pick the trigger to suit your code. The High level board sounds when the pin is HIGH and stays quiet while your board starts up, so choose it if you're unsure. The Low level board sounds when the pin is LOW, and on a 3.3V board such as an ESP32 or Pico its VCC goes to 3.3V, not 5V. An active buzzer makes one tone only, so it won't play a tune. For music or voice, use our SC8002B amplifier module with speaker.

Specifications

Buzzer12 mm active buzzer, one fixed tone of about 2 to 3 kHz
TriggerHigh level sounds when I/O is HIGH; Low level sounds when I/O is LOW
Supply3.3 to 5V DC on VCC, loudest at 5V
CurrentAbout 30 mA from VCC while it sounds; the I/O pin only supplies about 4 mA
Logic3.3V or 5V. Low level board on an ESP32 or Pico: run VCC from 3.3V
DriverTransistor with a 1k base resistor, so digitalWrite is all it needs
PinsVCC, I/O, GND on a right-angle 3-pin header (2.54 mm)
Wash sealSticker over the sound hole; peel it off for full volume
Board size32.2 x 13.1 mm, one 3 mm mounting hole

Datasheets

Wiring & getting started

Wiring diagramArduino Uno
Buzzer module wired to an Arduino Uno: VCC to 5V, I/O to D8, GND to GND
Tap the drawing to open it full size.
  1. Connect three wires

    The pin names are printed beside the header. VCC goes to 5V, I/O to D8 and GND to GND. On an ESP32 or Pico, use 3.3V for VCC with the Low level board. Three female jumper wires push straight onto the pins.

  2. Peel off the seal

    The sticker on top covers the sound hole while boards are washed in the factory. Leave it on and the beep is muffled, so peel it off once the module is in place.

  3. Load the test code

    Upload this sketch to an Uno. For the Low level board, change ACTIVE_LEVEL to LOW first.

    Example Arduino codeArduino C++
    // Active buzzer module test (MOD-BUZ-ACT-H / MOD-BUZ-ACT-L).
    // Module VCC to 5V, I/O to D8, GND to GND on the Uno.
    // High level board: set ACTIVE_LEVEL to HIGH.
    // Low level board:  set ACTIVE_LEVEL to LOW.
    const int BUZ = 8;
    const int ACTIVE_LEVEL = HIGH;
    const int IDLE_LEVEL = (ACTIVE_LEVEL == HIGH) ? LOW : HIGH;
    
    void beep(int ms) {
      digitalWrite(BUZ, ACTIVE_LEVEL);  // buzzer on
      delay(ms);
      digitalWrite(BUZ, IDLE_LEVEL);    // buzzer off
    }
    
    void setup() {
      digitalWrite(BUZ, IDLE_LEVEL);  // set the off level first
      pinMode(BUZ, OUTPUT);           // so it stays quiet at start
    }
    
    void loop() {
      beep(100);   // two short beeps
      delay(150);
      beep(100);
      delay(1000);
      beep(600);   // one long beep
      delay(2000);
    }
  4. Check it works

    You should hear two short beeps, a pause and one long beep, repeating every few seconds. If a Low level board beeps as your board starts, set the pin HIGH before making it an output, as the sketch does. If it keeps buzzing on a 3.3V board, move VCC from 5V to 3.3V.

Frequently Asked Questions

Answers to the questions buyers ask most.

Should I buy the High level or Low level version?
If you're not sure, get High level. It beeps when the pin is HIGH, stays quiet while your board starts up and works from any 3.3V or 5V pin. Low level suits code or alarm boards that pull a pin LOW to signal.
Can it play tunes or different notes?
No. An active buzzer has its own oscillator and makes one fixed tone, so tone() with different notes won't give you a melody. Use digitalWrite to turn it on and off for beeps and patterns. For music, a speaker with an amplifier is the right part.
Will it work with an ESP32, Pico or other 3.3V board?
Yes. The High level board works with VCC on 3.3V or 5V. The Low level board needs VCC on 3.3V when it's driven from a 3.3V pin, because with VCC on 5V a 3.3V HIGH can't switch it off and it keeps buzzing. It's loudest at 5V and a little quieter at 3.3V.
Why does my Low level buzzer beep when the board powers up?
While a board boots, its pins float until your code sets them, and a Low level board can sound during that time. Write the pin HIGH and then set it as an output in setup(), and keep the start-up short. If any beep at power-up is a problem, use the High level board.
Should I remove the sticker?
Yes. It's a seal that keeps water out of the sound hole while boards are washed after soldering. It muffles the beep, so peel it off for full volume.
Can I connect it straight to a microcontroller pin?
Yes. The transistor on the board carries the buzzer current, about 30 mA, so the I/O pin only supplies about 4 mA. Power VCC from your board's 5V or 3.3V pin and join the grounds.

Have a Question About This Product?

Send it through and we will get back to you by email.

Why Buy from NZN

Useful parts, fair prices and someone local to help.

I'm Lukas, an engineering student and maker based in Te Awamutu. NZN grew out of a CNC build that dragged on for months because every missing cable, bolt or electronic part meant another overseas order. I started the shop so Kiwi makers can spend more time building and less time waiting for the next parcel.

  • Stocked here in New Zealand

    Orders are picked and packed in Te Awamutu and dispatched within 24 hours every day, excluding public holidays. NZ Post target delivery is 1-2 days urban and 2-4 days rural. In Te Awamutu and Kihikihi you can choose local delivery at checkout: same day if you order before 8am, otherwise next day.

  • Fair prices, clearly shown

    Prices are kept competitive and quantity discounts are shown upfront. Free delivery starts at $50 for urban addresses and $88 for rural addresses.

  • 30-day returns and 12-month warranty

    Get in touch if something is not right and we will help sort it.

  • Practical product support

    Ask a product question and get help from a real person in New Zealand who knows the range.

You may also like