Clearance
Lines we're clearing out and won't restock.
17 parts clearing out. Best sellers first, while stock lasts.
No clearance parts match those filters.
-
IEC C14 Panel Mount Power Inlet 10A 250V
A three-pole IEC 60320 C14 appliance inlet for fitting a removable C13 mains lead to an equipment enclosure. The current NZN stock is marked AC-04 and 10A 250V AC, with a two-hole screw flange and rear solder tabs.
$1.49$2.99You save $1.50
10+ in stock
-
Metal Film Resistor Kit - 600pc, 30 Values, Damaged Case
A 600-piece 1/4W metal film resistor kit with 30 values from 10Ω to 1M, 20 of each, at ±1% tolerance. Every value sits on its own paper tape with the value printed on it, and the printed card in the lid lists the full range, so you can find the one you need quickly. Ideal bench stock for Arduino, ESP32 and general electronics work.
-
E-Switch 100SP5 Mini Toggle Switch - SPDT ON-OFF-(ON) Momentary, PCB Pins
This mini toggle switch stays on one way and springs back the other. Flick the lever towards ON and it stays there. In the middle it is off. Push it towards (ON) and it connects only while you hold it, then springs back to off when you let go. So one lever gives you run in one direction and a short jog or reset pulse in the other.
$5.99You save $0.00
5 in stock
-
BI 7386 3-Turn Wirewound Precision Potentiometer - 10k Linear, 1.5W
This is a precision panel pot for when a normal single-turn knob is too coarse. The shaft turns three full turns from end to end, so each turn covers about a third of the range and you can set a voltage, a power supply output or a position reference much more finely. The 10k track is wound from resistance wire, which keeps it stable with temperature and gives a linearity of 0.25%.
$34.99You save $0.00
1 in stock
-
NKK S9AWF Momentary Toggle Switch - SPDT ON-OFF-(ON), 20A 30VDC, 6A 250VAC
A momentary toggle switch does two jobs with one lever. Flick this NKK S9AWF one way and it stays on. Leave it in the middle and it is off. Push it the other way and it stays on only while you hold it, then springs back to off when you let go. That suits a 12V bilge pump panel, with auto one way and hold-for-manual the other, or a workshop machine with run one way and jog the other.
$29.99You save $0.00
1 in stock
-
JIU YE FENG JYF-50S 50mm Inline Duct Fan 12V 6W
A JYF-50S inline fan that sits in a run of 50mm (2 inch) pipe or hose and pulls air through it at up to 36 m³/h, about 21 CFM. That is the right size for venting a 3D printer enclosure, an electronics cabinet, a battery box or a composting toilet, and too small for a grow tent or bathroom. It runs from 12V DC at 6W, so a 12V plug pack or a 12V battery powers it. No power supply comes with it: the short lead ends in a female DC barrel socket, ready for a 12V supply with a barrel plug.
$36.99You save $0.00
1 in stock
-
12V Cigarette Lighter Socket - Panel Mount with Rubber Cap
A panel-mount 12V accessory socket in the standard cigarette-lighter size, so a phone charger, GPS, dash cam, tyre inflator or any other 12V plug-in device can run from a vehicle, boat, caravan or battery box. A rubber cap on a strap closes the front and keeps dust and dirt out when nothing is plugged in.
$7.99You save $0.00
1 in stock
-
RLEIL RL1-3 Rocker Switch 30x11mm Cut-out - ON/OFF, 10A 250VAC
A rocker switch is the panel-mounted ON/OFF switch you see on heaters, fans, power tools and bench gear. This one is a full-size RLEIL RL1-3 single-pole switch that clicks into a 30 x 11 mm rectangular hole and breaks one wire: press I to turn the circuit on and O to turn it off. It is moulded with a 10(4)A 250VAC rating, which means up to 10 A on a heater or lamp load and up to 4 A on a motor at 230V.
$3.99You save $0.00
1 in stock
-
12mm Rotary Encoder 3-Pin - Detentless Smooth Turn, No Push Switch
A rotary encoder is a knob that tells a microcontroller which way and how far it has been turned, and it spins endlessly with no end stops. This 12mm one turns smoothly with no clicks and gives 24 pulses a turn on two A/B channels, so an Arduino, ESP32 or Pico can read both direction and speed.
$3.89$4.99You save $1.10
4 in stock
-
PBS-33B 12mm Momentary Push Button, Pre-Wired
The PBS-33B 12mm momentary push button with two 20AWG leads already soldered on and sleeved in heat-shrink, so you can fit it and wire it straight into your project. It fits a 12mm panel hole, is rated 3A at 125V AC or 1A at 250V AC, and closes the circuit only while held down. Choose all-black leads or a red and black pair.
$0.99$1.59You save $0.60
3 in stock
-
MK8 Hardened Steel Nozzle - M6, 1.75mm Filament
A hardened steel drop-in nozzle for MK8-style hotends, with an M6 thread for 1.75mm filament. MK8 is the classic Creality-style nozzle found on the Ender 3, Ender 5 and CR-10, so this is a direct upgrade that lets those popular machines print abrasive filaments without wearing out. Hardened steel is wear-resistant, standing up to carbon fibre, glow-in-the-dark, wood- and metal-fill filaments that quickly chew through brass, and it handles higher temperatures too. Pick your tip: 0.8mm for balanced faster printing, 1.0mm for high-flow speed, 1.2mm for large-format work, or 1.5mm for extra-wide, maximum-flow printing. Fits straight in, no modifications needed.
$1.79$2.99You save $1.20
2 in stock
-
MK8 Brass Nozzle - M6, 1.75mm Filament
A brass drop-in nozzle for MK8-style hotends, with an M6 thread for 1.75mm filament. MK8 is the classic Creality-style nozzle found on the Ender 3, Ender 5, CR-10 and many other popular machines, so it drops straight in as a no-fuss replacement for a worn or clogged tip. Brass has the best thermal conductivity of any nozzle material, so it heats fast and prints cleanly on everyday, non-abrasive filaments. Pick your tip: 0.2mm for fine detail, 0.6mm for crisp everyday printing, 0.8mm for faster, stronger prints, or 1.0mm for high-flow, thick-layer work. Fits straight in, no modifications needed.
$0.49$0.99You save $0.50
3 in stock
-
Volcano Hardened Steel Nozzle - M6, 1.75mm Filament
Clearance - final units. We are narrowing our 3D printer range to focus on electronics, so this nozzle will not be restocked. These are brand new nozzles from our normal stock, not seconds, and our 12 month warranty still applies.
$2.49$3.99You save $1.50
10 in stock
-
Volcano Stainless Steel Nozzle - M6, 1.75mm Filament
A stainless steel drop-in nozzle for E3D Volcano-style hotends, with an M6 thread for 1.75mm filament. The Volcano's longer melt zone pushes far higher flow than a standard V6 nozzle, ideal for fast printing, thick layers and large-format parts. Stainless steel runs cleaner than brass, resists corrosion, contains no lead and holds up better to mildly abrasive and higher-temperature filaments. Available in 1.0mm and 1.2mm for maximum high-flow output. Fits straight in, no modifications needed.
$1.79$2.99You save $1.20
5 in stock
-
Volcano Brass Nozzle - M6, 1.75mm Filament
A brass drop-in nozzle for E3D Volcano-style hotends, with an M6 thread for 1.75mm filament. The Volcano's longer melt zone heats a bigger column of filament, so it pushes much higher flow than a standard V6 nozzle, ideal for fast printing, thick layers and large-format parts. Brass has the best thermal conductivity of any nozzle material, so it heats fast and keeps up on everyday, non-abrasive filaments. Pick your tip: 0.2mm or 0.3mm for fine detail, 0.6mm for crisp everyday work, 0.8mm for a balanced faster print, or 1.0mm and 1.2mm for maximum high-flow output. Fits straight in, no modifications needed.
$1.19$1.99You save $0.80
9 in stock
-
E3D V6 Hardened Steel Nozzle - M6, 1.75mm Filament
A hardened steel drop-in replacement nozzle for E3D V6-style hotends, with an M6 thread for 1.75mm filament. Pick your tip: 0.4mm for everyday detail printing, 1.0mm for high-flow speed, 1.2mm for large-format work, or 1.5mm for extra-wide, maximum-flow printing. Hardened steel is wear-resistant, so it stands up to abrasive and composite filaments (carbon fibre, glow-in-the-dark, wood- and metal-fill) that quickly chew through brass, and the steel handles temperatures up to ~500C. Fits straight in, no modifications needed.
$1.99$3.49You save $1.50
5 in stock
-
E3D V6 Stainless Steel Nozzle - M6, 1.75mm Filament
A stainless steel drop-in replacement nozzle for E3D V6-style hotends, with an M6 thread for 1.75mm filament. Pick your tip: 0.5mm for a strong all-round balance of speed and quality, 0.8mm for faster, stronger prints, or 1.0mm for high-flow, large-format work. Stainless steel is food-safe and corrosion resistant, making it the natural pick for food-contact prints and everyday printing where you want better durability than brass without stepping up to fully hardened steel. Fits straight in, no modifications needed.
$1.39$2.49You save $1.10
3 in stock
Frequently asked questions
How fast is shipping within New Zealand?
Orders are dispatched within 24 hours, every day except public holidays. NZ Post delivery is usually 1-2 business days to urban addresses and 2-4 business days to rural addresses. Free shipping applies over $50 for urban addresses and $88 for rural addresses.
What is your returns policy?
We offer a 30-day returns policy. Change-of-mind returns are accepted on items that are unused, unmodified and in their original packaging. The customer pays return postage and the original shipping cost is non-refundable. Faulty or damaged items are covered at no cost to you.
Do your products come with a warranty?
Yes, all non-consumable items are covered by a 1-year warranty. If anything arrives faulty or stops working within the warranty period, contact us and we'll arrange a replacement or refund.
Is everything shown in stock in NZ?
Yes, we hold all listed stock locally in Te Awamutu, Waikato. There's no waiting on international shipping: what you see available ships within 24 hours.
What payment methods do you accept?
Checkout takes credit and debit cards, PayPal, Shop Pay, Apple Pay, Google Pay and Afterpay. Schools, clubs and businesses that need a formal quote first can send us a parts list from our Quick Order page.