Black KF301 2-pole screw terminal block, three-quarter view of the wire windows and two solder pins

KF301 2-Pin Screw Terminal Block - 5mm Pitch, Fits 5.08mm PCB, Black

$0.59 NZD
each Save 10% at 25+
Skip to product information
SKU: CON-KF301-508-2P-BLK

KF301 2-Pin Screw Terminal Block - 5mm Pitch, Fits 5.08mm PCB, Black

$0.59 NZD
Availability:
Order before 7:30am (12pm weekends) for same-day dispatch Dispatch 7 days a week, excluding public holidays

NZ Post: 1-2 days urban · 2-4 days rural

Shipping from $5.99 urban / $9.99 rural, or free pick-up in Te Awamutu.

Buy more, pay less Prices shown are per unit. Add enough of this item and the lower rate applies on its own at checkout. There is no code to enter and you do not need to buy a pack. Choosing a tier here just sets the quantity for you. Larger quantities go out in the same bag, so packing, handling and postage cost us less per unit. We pass that saving straight on to you, so you can buy more for less.

Minimum order quantity: 5

Easy 30-day returns · 12-month warranty

Add $50.00 for Free Urban delivery ($88.00 for Rural)
Urban $50 Rural $88

A KF301 is the standard two-pole screw terminal that solders into a circuit board and clamps a wire under a screw, so you can bring power, a motor, a sensor or a speaker lead onto a board without soldering the wire itself. This one is a 2-pin block at 5mm pitch that fits both 5.0mm and 5.08mm (0.2 inch) board footprints, black, with the wire opening on the front and the clamp screw on top.

It takes stranded or solid wire from about 22 to 16 AWG (0.3 to 1.3mm²), which covers hook-up wire, small DC leads and speaker wire. Thicker 14 AWG wire may not go in. We would keep it to low-voltage DC and signal wiring, up to about 5A per terminal. It carries no approval markings, so it is not for 230V mains. For a 4-way block, use two. They are sold in lots of 5 or more.

Specifications

Pitch5mm, fits 5.0mm and 5.08mm (0.2in) footprints
Poles2
MountingThrough-hole PCB, solder pins
Wire range22 to 16 AWG (0.3 to 1.3mm²)
Wire entryFront opening, clamp screw on top
ColourBlack

Wiring & getting started

  1. Solder it in first

    Push the block into the board with the wire openings facing the way you want the wires to come from, and solder the two pins from underneath. Do this before you wire it, so the heat does not reach the clamp screws.

  2. Strip and twist the wire

    Strip about 6mm of insulation and twist stranded wire tightly so no strand strays.

  3. Clamp the wire

    Back the screw off, push the bare wire into the front opening until it stops, and tighten the screw until the wire will not pull out. Stop when it is held. Forcing a small screw can strip the thread or crush the strands.

Frequently Asked Questions

Answers to the questions buyers ask most.

Is it 5.0mm or 5.08mm pitch?
Both numbers are used for this block. Makers of the KF301 family list it as 5.0mm, and many shops and PCB footprints call it 5.08mm (0.2 inch). On a 2-pin block the 0.08mm difference is smaller than the clearance in a normal through-hole, so it drops into a 5.08mm footprint. If you join several blocks into a long strip, the gap adds up to about 0.3mm over four poles, so test-fit one strip before you order boards.
Can I put two side by side for a 4-way terminal?
Yes. Solder two 2-pin blocks next to each other and you have a 4-way terminal. Check the spacing across the join on your own footprint first, since it can be a touch off 5.08mm.
What wire will fit, and do I need ferrules?
Wire from about 22 to 16 AWG fits well, stranded or solid. Strip about 6mm, twist the strands and push it to the stop. A ferrule is not needed, though a small bootlace ferrule keeps strands together if you rewire the block often. Thick 14 AWG wire is a tight fit and may not enter at all.
Can I use it for mains wiring?
No. This is a circuit board part with no approval markings on it, so keep it to low-voltage DC and signal wiring. For mains, use a block that carries its own rating and approval.
How much current can one terminal take?
We would use it up to about 5A per terminal for continuous loads, with the wire sized to match. The block carries no current marking, so we keep to that working limit.

Have a Question About This Product?

Send it through and we will get back to you by email.

Why Buy from NZN

Useful parts, fair prices and someone local to help.

I'm Lukas, an engineering student and maker based in Te Awamutu. NZN grew out of a CNC build that dragged on for months because every missing cable, bolt or electronic part meant another overseas order. I started the shop so Kiwi makers can spend more time building and less time waiting for the next parcel.

  • Stocked here in New Zealand

    Orders are picked and packed in Te Awamutu and dispatched within 24 hours every day, excluding public holidays. NZ Post target delivery is 1-2 days urban and 2-4 days rural. In Te Awamutu and Kihikihi you can choose local delivery at checkout: same day if you order before 8am, otherwise next day.

  • Fair prices, clearly shown

    Prices are kept competitive and quantity discounts are shown upfront. Free delivery starts at $50 for urban addresses and $88 for rural addresses.

  • 30-day returns and 12-month warranty

    Get in touch if something is not right and we will help sort it.

  • Practical product support

    Ask a product question and get help from a real person in New Zealand who knows the range.

You may also like