MT3608 USB-C boost converter module, three-quarter view showing the USB-C socket, 220 inductor, blue BONENS 3296 trimmer and SS34 diode

MT3608 USB-C Adjustable Boost Converter Module, 2-24V Step Up

$2.79 NZD
Save 5% at 3+
Skip to product information
SKU: PWR-MT3608-USBC

MT3608 USB-C Adjustable Boost Converter Module, 2-24V Step Up

$2.79 NZD
Availability:
Order before 7:30am (12pm weekends) for same-day dispatch Dispatch 7 days a week, excluding public holidays

NZ Post: 1-2 days urban · 2-4 days rural

Shipping from $5.99 urban / $9.99 rural, or free pick-up in Te Awamutu.

Buy more, pay less Prices shown are per unit. Add enough of this item and the lower rate applies on its own at checkout. There is no code to enter and you do not need to buy a pack. Choosing a tier here just sets the quantity for you. Larger quantities go out in the same bag, so packing, handling and postage cost us less per unit. We pass that saving straight on to you, so you can buy more for less.

Easy 30-day returns · 12-month warranty

Add $50.00 for Free Urban delivery ($88.00 for Rural)
Urban $50 Rural $88

An adjustable step-up converter built on the MT3608 chip, with a USB-C socket for power in. Plug it into a USB-A port or charger with a USB-A to USB-C lead and it lifts the 5V to whatever you set with the trimmer, such as 9V or 12V. You can also feed the VIN pads from a battery or other DC supply between 2V and 24V. The output is always higher than the input, so it will not lower a voltage. From a 5V supply, plan on up to about 5W at the output, which is 0.55A at 9V or 0.4A at 12V, and less from a lower-voltage battery. The 4A in the chip's datasheet is a peak switch limit inside the chip, not the current you can take from the board.

Specifications

Converter chipMT3608 step-up, 1.2MHz
Input voltage5V from the USB-C socket, or 2V to 24V on the VIN pads (chip range)
Output voltageAdjustable, always above the input, up to 28V (chip limit). We suggest 24V or less
Output currentUp to about 5W from a 5V supply (NZN limit): 0.55A at 9V, 0.4A at 12V. Less from a battery
Switch current limit4A peak inside the chip, not an output rating
AdjustmentMulti-turn trimmer, counter-clockwise raises the output
USB-C socketPower in only, 5V. Use a USB-A to USB-C lead: a USB-C only charger with a C to C lead may give nothing
ConnectionsVIN+ and VIN-, OUT+ and OUT- solder pads
Reverse polarityNot protected on the VIN pads
Inductor22µH (marked 220)
MountingNo mounting holes. The four corner holes are the VIN and OUT pads, so fix the board with foam tape, not metal screws
Board sizeAbout 30 x 17mm

Datasheets

Great for

Running a 9V guitar pedal or other 9V device from a USB charger
A 12V fan or a short run of LED lights, up to about 0.4A, from USB
Lifting one Li-ion cell (3.7V) to 5V for an Arduino or ESP32 board
A small bench supply for testing a project at a set voltage

Wiring & getting started

  1. Power it

    Plug a USB-A to USB-C lead into the board and a USB-A port or charger. To use a battery or other supply instead, solder it to VIN+ and VIN-, with the plus on VIN+. There is no reverse-polarity protection, so check before you connect.

  2. Set the voltage before the load

    With nothing on OUT+ and OUT-, put a multimeter across them. Turn the trimmer a little at a time. Counter-clockwise raises the voltage. It is a multi-turn trimmer, so if the meter just shows the input voltage, keep turning counter-clockwise, up to 20 turns. If your board moves the other way, follow the meter.

  3. Connect your project

    Once the meter shows the voltage you want, switch off, wire your project to OUT+ and OUT-, and power up again. With the load running, the voltage should hold steady and the chip, inductor and diode should be warm, not too hot to touch.

Frequently Asked Questions

Answers to the questions buyers ask most.

How much current can it supply?
From a 5V supply, plan on up to about 5W at the output, so the current falls as you raise the voltage: roughly 0.7A at 7V, 0.55A at 9V, 0.4A at 12V and 0.2A at 24V. From a single Li-ion cell, plan on about 0.7A at 5V. The chip has a 4A peak switch limit, but that is the current inside the chip, not what you can take from the output, and the small inductor and diode run hot well before it.
What can I power it from?
The USB-C socket takes 5V from a USB-A port or charger through a USB-A to USB-C lead. A 12V 0.4A load pulls about 1.1A from the 5V input, so use a charger rated 2A. A plain USB port gives about 0.5A, which limits you to roughly 2W at the output. The VIN pads take 2V to 24V if you would rather use a battery or a bench supply.
Will it work with a USB-C to USB-C cable?
Not reliably. The socket is power in only and does not ask a charger for power, so a USB-C only charger with a USB-C to USB-C lead may supply nothing. Use a USB-A to USB-C lead. The board also cannot ask for 9V or 12V from a fast charger, it only boosts the 5V.
Which way do I turn the trimmer?
Counter-clockwise raises the output. It is a multi-turn trimmer, so you may need up to 20 turns before the voltage starts to rise above the input. Watch a multimeter across OUT+ and OUT- while you turn it, and if your board moves the other way, follow the meter.
What voltage is it set to when it arrives?
The setting varies from board to board, so do not assume it. Measure OUT+ to OUT- with nothing connected and set the voltage you want before you wire in your project. A board set too high can destroy a 5V or 3.3V project.
Can the output be lower than the input?
No. This is a boost converter. With the trimmer turned right down the output sits just under the input, so from USB you will not get below about 4.7V. If you need a lower voltage, use a buck (step-down) module.
Does it have any protection?
No reverse-polarity protection on the VIN pads, so check the polarity first. The chip has current limiting and thermal shutdown, but do not rely on them. Nothing stops you setting the output too high for your load, which is why you measure first.
Does it get hot?
It gets warm in normal use. Near 5W the chip, inductor and diode run hot, so leave air around the board and stay under the limits above for continuous use.

Have a Question About This Product?

Send it through and we will get back to you by email.

Why Buy from NZN

Useful parts, fair prices and someone local to help.

I'm Lukas, an engineering student and maker based in Te Awamutu. NZN grew out of a CNC build that dragged on for months because every missing cable, bolt or electronic part meant another overseas order. I started the shop so Kiwi makers can spend more time building and less time waiting for the next parcel.

  • Stocked here in New Zealand

    Orders are picked and packed in Te Awamutu and dispatched within 24 hours every day, excluding public holidays. NZ Post target delivery is 1-2 days urban and 2-4 days rural. In Te Awamutu and Kihikihi you can choose local delivery at checkout: same day if you order before 8am, otherwise next day.

  • Fair prices, clearly shown

    Prices are kept competitive and quantity discounts are shown upfront. Free delivery starts at $50 for urban addresses and $88 for rural addresses.

  • 30-day returns and 12-month warranty

    Get in touch if something is not right and we will help sort it.

  • Practical product support

    Ask a product question and get help from a real person in New Zealand who knows the range.

You may also like