RV09 vertical potentiometer, 3-pin PCB mount, with ribbed slotted black shaft and metal shield

RV09 Vertical Potentiometer, 3-Pin PCB Mount, B Linear, 1K to 100K

1K
$1.19 NZD
Save 10% at 5+
Skip to product information
SKU: POT-RV09-B1K

RV09 Vertical Potentiometer, 3-Pin PCB Mount, B Linear, 1K to 100K

$1.19 NZD
Resistance
Availability:
Order before 7:30am (12pm weekends) for same-day dispatch Dispatch 7 days a week, excluding public holidays

NZ Post: 1-2 days urban · 2-4 days rural

Shipping from $5.99 urban / $9.99 rural, or free pick-up in Te Awamutu.

Buy more, pay less Prices shown are per unit. Add enough of this item and the lower rate applies on its own at checkout. There is no code to enter and you do not need to buy a pack. Choosing a tier here just sets the quantity for you. Larger quantities go out in the same bag, so packing, handling and postage cost us less per unit. We pass that saving straight on to you, so you can buy more for less.

Easy 30-day returns · 12-month warranty

Add $50.00 for Free Urban delivery ($88.00 for Rural)
Urban $50 Rural $88

An RV09 vertical potentiometer for soldering to a circuit board: three pins at 2.5mm pitch, two side tabs and a knurled shaft about 12.5mm long with a screwdriver slot. Choose 1K to 100K; 10K is the usual pick for an Arduino or ESP32 analogue input. The B marking means linear, so the reading changes evenly as you turn. Knob not included.

Specifications

Resistance options1K, 2K, 5K, 10K, 20K, 50K, 100K
Taper and toleranceB (linear), ±20%
RotationAbout 170°
ShaftAbout 12.5mm, knurled with a slot
BodyVertical, about 9.5mm wide
PinsThree, 2.5mm pitch (about 5mm end to end), centre wiper
MountingPCB through-hole with two side tabs (11.3mm apart)
UseSignal level only, up to 12V DC and 0.05W
Purchase quantityOne potentiometer per unit

Datasheets

Wiring & getting started

Wiring diagramArduino, ESP32 or similar
Wiring an RV09 potentiometer: the middle pin (wiper) goes to analogue input A0, one end pin goes to GND and the other end pin goes to 3.3V or 5V. Swap the end pins if the reading goes the wrong way.
Tap the drawing to open it full size.
  1. Know the pins

    The middle of the three pins is the wiper. The two outer pins are the ends of the track.

  2. Connect with power off

    Outer pins to 3.3V (or 5V) and GND, middle pin to an analogue input. Swap the outer pins if it turns the wrong way.

  3. Soldering or breadboard

    It is made for soldering. On a breadboard the side tabs stop it sitting flat, so squeeze them flat with pliers or snip them off. Keep the iron under 250°C and the soldering quick.

Note: Use it as a control signal only. Motors, LEDs and anything heavier need a driver circuit between the pot and the load.

Frequently Asked Questions

Answers to the questions buyers ask most.

Which value should I get?
10K suits most Arduino, ESP32 and Raspberry Pi Pico analogue inputs. Use 1K to 5K for small LED or audio level circuits, and 50K or 100K when the input is very high impedance or you want less current drawn.
Does B mean linear?
Yes. B is a linear taper, so turning the shaft changes the resistance in an even line. A is the log taper used in audio volume controls.
Will it fit on a breadboard?
Not flat. The two side tabs get in the way. Squeeze them flat with pliers or snip them off and the three pins fit, or solder wires to the pins instead.
Is a knob included?
No. The shaft is about 6mm across, knurled, with a screwdriver slot. Push-on knobs made for 6mm knurled shafts are the type to look for, but knurl patterns vary between makers, so a knob can be a snug or loose fit. A small screwdriver turns it too.
Can it control a motor or a bright LED directly?
No. It is a signal part rated for 0.05W, so use it to feed an analogue input or a driver circuit.
Can I panel-mount it with a nut?
No. This RV09 has no threaded bushing. It is meant for a circuit board behind a panel cut-out. For nut-and-washer panel mounting, see our WH148 potentiometers.

Have a Question About This Product?

Send it through and we will get back to you by email.

Why Buy from NZN

Useful parts, fair prices and someone local to help.

I'm Lukas, an engineering student and maker based in Te Awamutu. NZN grew out of a CNC build that dragged on for months because every missing cable, bolt or electronic part meant another overseas order. I started the shop so Kiwi makers can spend more time building and less time waiting for the next parcel.

  • Stocked here in New Zealand

    Orders are picked and packed in Te Awamutu and dispatched within 24 hours every day, excluding public holidays. NZ Post target delivery is 1-2 days urban and 2-4 days rural. In Te Awamutu and Kihikihi you can choose local delivery at checkout: same day if you order before 8am, otherwise next day.

  • Fair prices, clearly shown

    Prices are kept competitive and quantity discounts are shown upfront. Free delivery starts at $50 for urban addresses and $88 for rural addresses.

  • 30-day returns and 12-month warranty

    Get in touch if something is not right and we will help sort it.

  • Practical product support

    Ask a product question and get help from a real person in New Zealand who knows the range.

You may also like