TMC2208 stepper motor driver module with supplied blue heatsink, component side

TMC2208 Stepper Motor Driver Module with Heatsink

$7.49 NZD
Save 5% at 2+
Skip to product information
TMC2208 stepper motor driver module with supplied blue heatsink, component side
  • TMC2208 stepper motor driver module with supplied blue heatsink, component side
  • TMC2208 component-side top-down view showing the driver IC and soldered header pins
  • TMC2208 reverse-side top-down view showing the gold heatsink mounting area
  • TMC2208 stepper driver with the supplied blue aluminium heatsink installed
  • Supplied blue aluminium heatsink for the TMC2208 stepper driver
  • TMC2208 module dimensions 20.50 by 15.0 millimetres and 7 gram weight with heatsink
TMC2208 Stepper Motor Driver Module with Heatsink
SKU: MOD-TMC2208-1PK

TMC2208 Stepper Motor Driver Module with Heatsink

$7.49 NZD
Dispatch: Within 24 hours 7-day dispatch, excluding public holidays

NZ Post: 1-2 days urban · 2-4 days rural

Shipping from $5.99 urban / $9.99 rural.

Buy more, pay less Prices shown are per unit. Add enough of this item and the lower rate applies on its own at checkout. There is no code to enter and you do not need to buy a pack. Choosing a tier here just sets the quantity for you. Larger quantities go out in the same bag, so packing, handling and postage cost us less per unit. We pass that saving straight on to you, so you can buy more for less.

Easy 30-day returns · 12-month warranty

Free Urban delivery on orders over $66
Urban $66 Rural $88

A compact TMC2208 module for quiet bipolar stepper control in 3D printers, CNC machines and motion projects. It supports conventional STEP/DIR control or UART configuration, works with 3.3 V or 5 V logic, and includes a blue aluminium heatsink for the reverse-side thermal area.

Specifications

ControllerTMC2208-LA
Motor type2-phase bipolar stepper
Motor supply5 V to 36 V
Logic supply3.3 V or 5 V
Control modesSTEP/DIR or UART
Maximum output1.4 A
Recommended currentUp to 1.2 A with suitable cooling
Microstep interpolationUp to 256 microsteps
Standalone selection1/2, 1/4, 1/8 or 1/16 step
Header format2 × 8 pins, 2.54 mm pitch
Board size20.5 × 15.0 mm
WeightApprox. 7 g with heatsink

Datasheets

Full technical datasheet PDF Quick Start guide PDF

What's in the box

1×
TMC2208 driver module

Black board with both header rows soldered.

1×
Blue aluminium heatsink

Supplied loose with a thermal adhesive pad for the reverse-side gold area.

Great for

Quiet 3D printer motion
CNC and laser motion
Robotics
Compact automation projects

Wiring & getting started

  1. Switch off every supply

    Disconnect motor power, logic power and USB before inserting or wiring the module.

  2. Match every pin label

    Confirm VM, GND, VIO, DIR, STEP and EN against the carrier board. Do not rely on the board outline alone.

  3. Connect the motor phases

    Connect one winding to M1A and M1B, and the other winding to M2A and M2B.

  4. Fit the heatsink correctly

    Remove the protective film and place the flat adhesive base on the large gold thermal area on the reverse of the board.

  5. Choose the control mode

    Set the carrier-board jumpers and firmware for standalone STEP/DIR or UART operation.

  6. Start conservatively

    Begin at a low current setting, make a short slow move, then check motor direction and driver temperature.

Note: Never connect or disconnect motor windings while VM is powered. The module supplier states a 1.4 A maximum and recommends no more than 1.2 A with suitable cooling. Actual current capability depends on heatsink contact, airflow and the assembled machine.

Frequently Asked Questions

Answers to the questions buyers ask most.

Can I replace an A4988, TMC2209 or another StepStick driver with this module?
The board uses the common 2 x 8, 2.54 mm plug-in format, but socket orientation, signal routing and current settings vary. Match every pin label against the carrier board before applying power.
Do I have to use UART?
No. The module can run from conventional STEP/DIR signals in standalone mode. UART is available when the carrier board and firmware are configured for it.
Where does the heatsink go?
Fit the flat adhesive base to the large gold thermal area on the reverse of the board. Remove the protective film first and keep the heatsink clear of pins and the current-adjust trimmer.
How much current can it supply?
The module supplier states a 1.4 A maximum and recommends no more than 1.2 A with suitable cooling. Actual usable current depends on heatsink contact, airflow, supply voltage and the assembled machine, so start conservatively and monitor temperature.
Which standalone microstep settings are available?
The supplier table lists 1/2, 1/4, 1/8 and 1/16 step selections using MS1 and MS2. Follow the board diagram for the exact HIGH and LOW settings.
Can I connect the motor while the board is powered?
No. Switch off VM and logic power before connecting or disconnecting the motor, inserting the module, or changing carrier-board wiring.

Have a Question About This Product?

Send it through and we will get back to you by email.

Why Buy from NZN

Useful parts, fair prices and someone local to help.

I'm Lukas, an engineering student and maker based in Te Awamutu. NZN grew out of a CNC build that dragged on for months because every missing cable, bolt or electronic part meant another overseas order. I started the shop so Kiwi makers can spend more time building and less time waiting for the next parcel.

More about NZN Electronics

  • Stocked here in New Zealand

    Orders are picked and packed in Te Awamutu and dispatched within 24 hours every day, excluding public holidays. NZ Post target delivery is 1-2 days urban and 2-4 days rural.

  • Fair prices, clearly shown

    Prices are kept competitive and quantity discounts are shown upfront. Free delivery starts at $66 for urban addresses and $88 for rural addresses.

  • 30-day returns and 12-month warranty

    Get in touch if something is not right and we will help sort it.

  • Practical product support

    Ask a product question and get help from a real person in New Zealand who knows the range.

You may also like