1x2 2.54mm female pin header socket, front view, black housing with two silver-coloured solder tails

2.54mm Female Pin Header Socket, Single Row 2 to 40 Pin

1x2
$0.75 NZD
Save 20% at 5+
Skip to product information
SKU: HDR-254-F-1X02-ST

2.54mm Female Pin Header Socket, Single Row 2 to 40 Pin

$0.75 NZD
Size
Availability:
Order before 7:30am (12pm weekends) for same-day dispatch Dispatch 7 days a week, excluding public holidays

NZ Post: 1-2 days urban · 2-4 days rural

Shipping from $5.99 urban / $9.99 rural, or free pick-up in Te Awamutu.

Buy more, pay less Prices shown are per unit. Add enough of this item and the lower rate applies on its own at checkout. There is no code to enter and you do not need to buy a pack. Choosing a tier here just sets the quantity for you. Larger quantities go out in the same bag, so packing, handling and postage cost us less per unit. We pass that saving straight on to you, so you can buy more for less.

Easy 30-day returns · 12-month warranty

Add these too
Add $50.00 for Free Urban delivery ($88.00 for Rural)
Urban $50 Rural $88

A single-row female pin header is a strip of 2.54mm (0.1 inch) sockets. Solder it to your board and a module, a male pin strip or a Dupont jumper lead plugs in and pulls out again without more soldering. There are ten lengths from 2 to 40 pins: two 1x15 strips suit a 30 pin ESP32 board, and two 1x19 strips suit a 38 pin ESP32 board. These strips don't snap apart like male headers, so buy the length you need. Bulk discounts count each size on its own, so 5 of the same length qualify and a mix of lengths does not. For lots of sockets, cutting 1x40 strips is the cheapest per socket, but you lose one socket at every cut; ready-sized strips save the cutting and the lost socket. For the pins that plug into them, see the male 1x40 header.

Specifications

Pitch2.54mm (0.1 inch)
Housing and contactsBlack housing about 8.5mm tall, silver-coloured contacts, straight solder tails about 3mm long
TakesStandard 0.64mm square male header pins and Dupont male ends
MountingThrough-hole, 1.0mm holes on a 0.1 inch grid

Sizes

Size Length Good for
1x2 5.1mm Two-pin links and power connections
1x3 7.6mm 3-pin sensor modules (signal, power, ground)
1x4 10.2mm 4-pin I2C modules, such as small OLED displays
1x6 15.2mm 6-pin modules and USB-serial adapters
1x8 20.3mm 8-pin modules and breakout boards
1x12 30.5mm Longer module rows and display boards
1x15 38.1mm 30 pin ESP32 boards (two rows of 15)
1x19 48.3mm 38 pin ESP32 board (two per board)
1x20 50.8mm Raspberry Pi Pico (two per board)
1x40 101.6mm Cutting to your own lengths

Datasheets

Great for

Making an ESP32 board removable instead of soldering it down
Adding a plug-in sensor or display port to your own PCB or stripboard
Stacking a module on a carrier board with male pins underneath
Replacing a damaged socket on a module or shield

Wiring & getting started

  1. Choose the length

    Match the pin count to the row you are plugging in. To shorten a strip, cut through the middle of one socket with flush cutters. That socket is lost, so a 1x40 cut in two gives 39 sockets in all. Pull out the loose contact and file the end flat.

  2. Solder it square

    Plug your module or a male strip into the sockets first; it holds the strip straight while you solder. Tack one end pin, check it sits flat, then do the rest. Keep the heat short and go easy on extra flux, because flux that runs up into a socket can stop it gripping.

  3. Check, then plug in

    Look for solder bridges between neighbouring pins before powering up. Plug only header pins in. Thick resistor legs or meter probes stretch the contacts, and the socket stays loose afterwards. For quick links to a breadboard, use Dupont jumper wires.

Frequently Asked Questions

Answers to the questions buyers ask most.

Can I snap it to length like a male header?
No. Female strips have no snap-off notches. Cut through the middle of one socket with flush cutters and expect to lose that socket. For lots of sockets, cutting 1x40 strips is the cheapest per socket; for a few, buy the ready-sized length.
What plugs into it?
Standard 2.54mm (0.1 inch) male pins: a male pin header strip, the pins on a module, or the male end of a Dupont jumper lead.
Which size suits an ESP32 board?
A 30 pin ESP32 development board takes two 1x15, and a 38 pin board takes two 1x19. Count the pins on your own board before you order.
Why has a socket gone loose?
Usually something thicker than a header pin has been pushed in, such as a resistor leg or a meter probe, and stretched the contact. It won't grip properly again, so replace the strip.
Is the price per pin or per header?
Per header, one strip of the length you pick. Buying 5 or more of the same size, or 10 or more, lowers the price per header, as shown in the bulk price table. Each size is counted on its own, so 3 of one length and 2 of another don't add up.
Do I need to solder it?
Yes. It has through-hole solder tails and needs soldering to a board. Plug the module in while you solder so the strip stays straight.

Have a Question About This Product?

Send it through and we will get back to you by email.

Why Buy from NZN

Useful parts, fair prices and someone local to help.

I'm Lukas, an engineering student and maker based in Te Awamutu. NZN grew out of a CNC build that dragged on for months because every missing cable, bolt or electronic part meant another overseas order. I started the shop so Kiwi makers can spend more time building and less time waiting for the next parcel.

  • Stocked here in New Zealand

    Orders are picked and packed in Te Awamutu and dispatched within 24 hours every day, excluding public holidays. NZ Post target delivery is 1-2 days urban and 2-4 days rural. In Te Awamutu and Kihikihi you can choose local delivery at checkout: same day if you order before 8am, otherwise next day.

  • Fair prices, clearly shown

    Prices are kept competitive and quantity discounts are shown upfront. Free delivery starts at $50 for urban addresses and $88 for rural addresses.

  • 30-day returns and 12-month warranty

    Get in touch if something is not right and we will help sort it.

  • Practical product support

    Ask a product question and get help from a real person in New Zealand who knows the range.

You may also like