Black 9V PP3 battery box with ON/OFF slide switch and red and black leads, three-quarter view of the switch face

9V Battery Holder with Switch and Cover - PP3 Case with Wire Leads

$3.99 NZD
Save 5% at 3+
Skip to product information
SKU: BH-9V-SW

9V Battery Holder with Switch and Cover - PP3 Case with Wire Leads

$3.99 NZD
Availability:
Order before 7:30am (12pm weekends) for same-day dispatch Dispatch 7 days a week, excluding public holidays

NZ Post: 1-2 days urban · 2-4 days rural

Shipping from $5.99 urban / $9.99 rural, or free pick-up in Te Awamutu.

Buy more, pay less Prices shown are per unit. Add enough of this item and the lower rate applies on its own at checkout. There is no code to enter and you do not need to buy a pack. Choosing a tier here just sets the quantity for you. Larger quantities go out in the same bag, so packing, handling and postage cost us less per unit. We pass that saving straight on to you, so you can buy more for less.

Easy 30-day returns · 12-month warranty

Add these too
Add $50.00 for Free Urban delivery ($88.00 for Rural)
Urban $50 Rural $88

This is a closed black case for one 9V (PP3) battery, with an on/off slide switch on the base and red and black wire leads. The battery presses straight onto two snap studs built into the end of the case, so there is no separate snap clip to work loose, and the lid slides shut over it. You can switch a project off without pulling a wire or taking the battery out. Battery not included.

It suits guitar pedals, alarms, LED and buzzer circuits, sensors, small boards and test gear: anything that draws tens of milliamps. The leads end in bare tinned wire with no plug, so they clamp straight into screw terminals, such as our DC barrel jack screw terminal adapter, or you solder them to a board, header pins or Dupont jumper wires for a breadboard.

Specifications

Holds1 x 9V (PP3 / 6F22 / 6LR61) battery, not included
Voltage9V nominal, set by the battery you fit
Battery contactsSnap studs moulded into the case, battery presses on
SwitchON/OFF slide switch on the base, at the lead end
LeadsRed (+) and black (-), approx. 15cm, bare tinned ends
LidSlides on and clips shut; screw hole at the lead end (screw not included)
Polarity marks+ and - moulded in the floor of the case
Size (approx.)68 x 33 x 21mm
WeightApprox. 20g without the battery

Datasheets

Wiring & getting started

  1. Connect the leads first

    Red is positive and black is negative. Join each lead to your circuit before the battery goes in. The tinned ends clamp straight into screw terminals. For a breadboard, solder each end to a male header pin or a cut Dupont jumper wire so it plugs in, as bare stranded wire is too soft to push into the holes. Or solder the ends to your board. Tape the leads down so a tug pulls on the tape, not on the thin wire where it leaves the case.

  2. Fit the battery

    Slide the switch to OFF. Slide the lid off, then press the battery onto the two studs at the end of the case. The battery's terminals are different sizes, so it only fits one way round. Lay it flat and slide the lid back on until it clips shut. If the project gets knocked about, put a small screw through the hole at the lead end to stop the lid sliding off.

  3. Switch on and check

    Slide the switch to ON. A multimeter across the two leads should read about 9V with a fresh alkaline battery. No reading means the switch is still off or the battery is not fully pressed onto the studs.

  4. Switch off when you finish

    A 9V battery suits circuits that draw tens of milliamps. Switch off between uses so the circuit does not flatten it.

Note: Keep the two bare lead ends apart while the battery is in and the switch is on. A short across them heats the thin wires and the battery quickly.

Frequently Asked Questions

Answers to the questions buyers ask most.

Does it come with a battery?
No. It holds one 9V battery, which you supply. Alkaline, lithium and rechargeable 9V batteries all fit as long as they are the standard PP3 size with the usual two snap terminals.
Is there a plug or snap on the leads? How do I connect them?
No. The red and black leads end in bare tinned wire. Clamp them in a screw terminal, such as our DC barrel jack screw terminal adapter, or solder them to your board. For a breadboard, solder each end to a male header pin or a cut Dupont jumper wire so it plugs in.
Where is the switch, and how do I mount the case?
The ON/OFF slide switch is on the base, near the end the leads come out. Stick the case down by one long side with double-sided foam tape, so the switch stays reachable and the lid can still slide off for a new battery.
What can I power with it?
Anything that wants 9V and draws tens of milliamps: guitar pedals, alarms, LED and buzzer circuits, sensors and small boards. Check what your circuit draws, because a 9V battery can't supply much current and goes flat quickly under heavy loads such as motors. For those, use a 4 x AA holder or a proper supply.
How long will a 9V battery last?
A 9V alkaline battery holds about 600mAh at a 10mA load, falling to about 450mAh at 50mA. That is roughly 60 hours at 10mA and 9 hours at 50mA. Many circuits stop working before the battery is fully flat, so expect a bit less. For projects that run for days, use a plug-in supply or a bigger battery pack.
The battery is hard to fit or the lid is stiff. What do I do?
Line the battery's small round terminal up with the + mark and press it straight down onto both studs; the first fit is the tightest. Slide the lid along its rails rather than prising at the edges. If the lid comes open too easily in use, fit a small screw through the hole at the lead end.

Have a Question About This Product?

Send it through and we will get back to you by email.

Why Buy from NZN

Useful parts, fair prices and someone local to help.

I'm Lukas, an engineering student and maker based in Te Awamutu. NZN grew out of a CNC build that dragged on for months because every missing cable, bolt or electronic part meant another overseas order. I started the shop so Kiwi makers can spend more time building and less time waiting for the next parcel.

  • Stocked here in New Zealand

    Orders are picked and packed in Te Awamutu and dispatched within 24 hours every day, excluding public holidays. NZ Post target delivery is 1-2 days urban and 2-4 days rural. In Te Awamutu and Kihikihi you can choose local delivery at checkout: same day if you order before 8am, otherwise next day.

  • Fair prices, clearly shown

    Prices are kept competitive and quantity discounts are shown upfront. Free delivery starts at $50 for urban addresses and $88 for rural addresses.

  • 30-day returns and 12-month warranty

    Get in touch if something is not right and we will help sort it.

  • Practical product support

    Ask a product question and get help from a real person in New Zealand who knows the range.

You may also like