Purple BME280 temperature, humidity and pressure sensor module with a loose 6-pin header

BME280 Temperature, Humidity and Pressure Sensor Module 3.3V

$12.49 NZD
Save 4% at 3+
Skip to product information
SKU: BME280-3V3

BME280 Temperature, Humidity and Pressure Sensor Module 3.3V

$12.49 NZD
Availability:
Order before 7:30am (12pm weekends) for same-day dispatch Dispatch 7 days a week, excluding public holidays

NZ Post: 1-2 days urban · 2-4 days rural

Shipping from $5.99 urban / $9.99 rural, or free pick-up in Te Awamutu.

Buy more, pay less Prices shown are per unit. Add enough of this item and the lower rate applies on its own at checkout. There is no code to enter and you do not need to buy a pack. Choosing a tier here just sets the quantity for you. Larger quantities go out in the same bag, so packing, handling and postage cost us less per unit. We pass that saving straight on to you, so you can buy more for less.

Easy 30-day returns · 12-month warranty

Add these too
Add $50.00 for Free Urban delivery ($88.00 for Rural)
Urban $50 Rural $88

A BME280 sensor on a small 3.3V breakout board. One chip reads air temperature, relative humidity and air pressure, which makes it the usual pick for an ESP32 or Raspberry Pi Pico weather station, a room climate sensor in Home Assistant, or a logger that tracks pressure trends.

It's set up for I2C at address 0x76, so you only need four wires, and it can also run on SPI. There's no regulator on the board, so it runs on 3.3V only and 5V on any pin will damage it. A 5V Arduino Uno or Nano needs our 4-channel logic level converter between the two boards, or you can use our BME280 5V module, which has a regulator and level shifting built in. The 6-pin header comes loose for you to solder. If you only need pressure and temperature, our BMP280 3.3V module costs less.

Specifications

SensorBME280, chip ID 0x60
MeasuresTemperature, humidity and air pressure
Supply3.3V only, no regulator
InterfaceI2C at 0x76 as supplied, or SPI
Humidity0 to 100% RH, ±3% RH typical
Pressure300 to 1100 hPa, ±1 hPa typical
Temperature-40 to +85°C, ±0.5°C typical from 0 to 65°C
Board sizeApprox. 15.5 x 11.5 mm, two 3 mm holes
In the box1 module and a 6-pin header, not soldered

Datasheets

Wiring & getting started

Wiring diagramESP32
BME280 module wired to an ESP32: VCC to 3V3, GND to GND, SDA to GPIO21, SCL to GPIO22, with CSB and SDO left unconnected
Tap the drawing to open it full size.
  1. Solder the header

    Solder the 6-pin header to the pads. Keep flux and cleaner away from the tiny hole in the top of the sensor, because that's where the air gets in.

  2. Wire it up

    On an ESP32: VCC to 3V3, GND to GND, SDA to GPIO21 and SCL to GPIO22. On a Pico, SDA goes to GP4 and SCL to GP5. Leave CSB and SDO unconnected. The board already sets it to I2C at address 0x76.

  3. Load the test code

    In the Arduino IDE, install the Adafruit BME280 library from the Library Manager. Upload this sketch and open the Serial Monitor at 115200 baud.

    Example Arduino codeArduino C++
    // BME280 3.3V module test.
    // VCC to 3.3V, GND to GND, SDA and SCL to the I2C pins.
    #include <Wire.h>
    #include <Adafruit_BME280.h>
    
    Adafruit_BME280 bme;
    
    void setup() {
      Serial.begin(115200);
      if (!bme.begin(0x76)) {  // this board is set to 0x76
        Serial.println("No BME280 found at 0x76. Check the wiring.");
        while (true) delay(10);
      }
      Serial.print("Chip ID 0x");
      Serial.println(bme.sensorID(), HEX);  // 60 = BME280
    }
    
    void loop() {
      Serial.print(bme.readTemperature(), 1);
      Serial.print(" C   ");
      Serial.print(bme.readHumidity(), 0);
      Serial.print(" %RH   ");
      Serial.print(bme.readPressure() / 100.0, 1);
      Serial.println(" hPa");
      delay(2000);
    }
  4. Check it works

    You should see Chip ID 0x60, then a line every 2 seconds such as 21.4 C 55 %RH 1013.2 hPa. If it says no BME280 was found, check that SDA and SCL aren't swapped and that VCC is on 3V3, not 5V.

  5. Use it in ESPHome (optional)

    ESPHome looks for the sensor at 0x77 unless you tell it otherwise, so add address: 0x76 to the sensor block.

    ESPHome configESPHome YAML
    i2c:
      sda: GPIO21
      scl: GPIO22
    
    sensor:
      - platform: bme280_i2c
        address: 0x76
        temperature:
          name: "Temperature"
        humidity:
          name: "Humidity"
        pressure:
          name: "Pressure"

Frequently Asked Questions

Answers to the questions buyers ask most.

How do I know it's a BME280 and not a BMP280?
Run the test sketch and read the chip ID it prints. A BME280 reads 0x60 and measures humidity. A BMP280 reads 0x58, has no humidity sensor, and the Adafruit BME280 library won't start with one. The BME280 sits in a square metal case with a small hole in the top; the BMP280 case is narrower and rectangular.
Can I use it with an Arduino Uno or Nano?
Not directly. The board has no regulator or level shifting, so the Uno's 5V signals would damage the sensor. Power it from the Uno's 3.3V pin and put our 4-channel logic level converter between the two boards on SDA and SCL.
Why does it read a degree or two warmer than the room?
The sensor measures its own chip temperature, and it warms slightly each time it takes a reading. Take readings less often (once a minute is plenty for a weather station) and mount the board on short wires away from the ESP32 and any regulator. If it still reads high, set a temperature offset in your code or in ESPHome.
Can I use two of them on the same I2C bus?
Yes. Leave SDO unconnected on one so it stays at 0x76, and connect SDO to 3.3V on the other to move it to 0x77. Then start each one at its own address in your code.
Can I use it outdoors?
Yes, inside a vented shelter that keeps rain and direct sun off it but lets air through. Water or condensation on the board makes humidity read near 100% until it dries out, and direct sun pushes the temperature reading well above the real air temperature.
Why is the humidity reading off after soldering or cleaning?
Heat, flux and solvents such as isopropyl alcohol upset the humidity sensor for a while. Keep cleaner off the sensor, and if the reading has drifted, leave the board in normal room air for about five days and it settles back.
Does it work with a Raspberry Pi?
Yes. Connect VCC to pin 1 (3.3V), GND to pin 6, SDA to pin 3 and SCL to pin 5, then turn on I2C in raspi-config. Running i2cdetect -y 1 should show the sensor at 76.

Have a Question About This Product?

Send it through and we will get back to you by email.

Why Buy from NZN

Useful parts, fair prices and someone local to help.

I'm Lukas, an engineering student and maker based in Te Awamutu. NZN grew out of a CNC build that dragged on for months because every missing cable, bolt or electronic part meant another overseas order. I started the shop so Kiwi makers can spend more time building and less time waiting for the next parcel.

  • Stocked here in New Zealand

    Orders are picked and packed in Te Awamutu and dispatched within 24 hours every day, excluding public holidays. NZ Post target delivery is 1-2 days urban and 2-4 days rural. In Te Awamutu and Kihikihi you can choose local delivery at checkout: same day if you order before 8am, otherwise next day.

  • Fair prices, clearly shown

    Prices are kept competitive and quantity discounts are shown upfront. Free delivery starts at $50 for urban addresses and $88 for rural addresses.

  • 30-day returns and 12-month warranty

    Get in touch if something is not right and we will help sort it.

  • Practical product support

    Ask a product question and get help from a real person in New Zealand who knows the range.

You may also like