ESP32-S3 DevKitC N16R8 board with two USB-C ports and two loose yellow 22-pin header strips, three-quarter view

ESP32-S3 DevKitC-Style N16R8 Dev Board - 16MB Flash, 8MB PSRAM, Dual USB-C, WiFi + BLE 5

Unsoldered
$16.99 NZD
Save 3% at 3+
Skip to product information
SKU: ESP32-S3-DEVKITC-N16R8-1PK

ESP32-S3 DevKitC-Style N16R8 Dev Board - 16MB Flash, 8MB PSRAM, Dual USB-C, WiFi + BLE 5

$16.99 NZD
Headers
Availability:
Order before 7:30am (12pm weekends) for same-day dispatch Dispatch 7 days a week, excluding public holidays

NZ Post: 1-2 days urban · 2-4 days rural

Shipping from $5.99 urban / $9.99 rural, or free pick-up in Te Awamutu.

Buy more, pay less Prices shown are per unit. Add enough of this item and the lower rate applies on its own at checkout. There is no code to enter and you do not need to buy a pack. Choosing a tier here just sets the quantity for you. Larger quantities go out in the same bag, so packing, handling and postage cost us less per unit. We pass that saving straight on to you, so you can buy more for less.

Easy 30-day returns · 12-month warranty

Add $50.00 for Free Urban delivery ($88.00 for Rural)
Urban $50 Rural $88

This is an ESP32-S3 development board for projects that need more memory than an ordinary ESP32 can give you. It carries 16MB of flash for your program and files, and 8MB of PSRAM, the extra working memory that makes camera frames, screens, audio buffers and larger web pages or small AI models practical. The ESP32-S3 has two 240MHz cores, WiFi, Bluetooth 5 LE and USB support built into the chip, and you can program it in Arduino, MicroPython, CircuitPython, ESPHome or ESP-IDF. It is a compatible board with the same style of pin labels as Espressif's DevKitC-1, not Espressif's own board, so a project that only needs WiFi and a few sensors is cheaper on our 30-pin ESP32-WROOM-32 board.

Two things catch people out, so here they are first. The module is octal PSRAM, so in Arduino IDE you must set PSRAM to OPI PSRAM, and pins GPIO35, 36 and 37 are used by that memory and can't be used for your own wiring, even though they are labelled on the board. The board also has two USB-C ports. The one marked COM goes through a serial chip and the one marked USB talks to the ESP32-S3 directly. Use either for power and uploads, but plug in one at a time while you are learning. The pins run at 3.3V, so any part that sends 5V signals needs a logic level converter. The board is wide, so on one standard breadboard it leaves almost no free holes beside the pins; two breadboards side by side work well. Choose Soldered to plug it straight in, or Unsoldered if you would rather fit the two loose 22-pin strips yourself.

Specifications

ModuleESP32-S3-N16R8 (printed on the metal can), with a PCB antenna at the end opposite the USB-C ports
ProcessorESP32-S3 chip: dual-core Xtensa LX7 up to 240MHz, 512KB SRAM, vector instructions for AI work
Flash and PSRAM16MB flash and 8MB octal PSRAM (the N16R8 in the module name)
Wireless2.4GHz WiFi 802.11 b/g/n and Bluetooth 5 LE. No 5GHz WiFi
USBTwo USB-C ports: COM through a WCH CH343P serial chip (may need its driver), and USB direct to the ESP32-S3 for serial, JTAG and USB keyboard, mouse or MIDI
Logic voltage3.3V, not 5V tolerant
Power in5V from either USB-C port, or 5V on the 5Vin pin. Do not power it from the 5Vin pin and USB at the same time
Regulator3.3V linear regulator marked 1117. Power small sensors and displays from the 3V3 pins, not motors or LED strips
Pins2 rows of 22 at 2.54mm pitch, labelled with their GPIO numbers (GPIO0 to 21 and 35 to 48, with GPIO43 and 44 shown as TX and RX), plus 3V3, 5Vin, GND and RST
Pins you can't useGPIO35, 36 and 37 are taken by the octal PSRAM. Leave them unconnected
Startup pinsGPIO0 is the BOOT button. GPIO3, 45 and 46 are read at power-up, so don't hold them high or low with a circuit
Onboard LEDsOne RGB LED, wired to a pin only after you bridge the RGB solder pad (open on our boards), plus three small indicator LEDs
ButtonsRST (reset) and BOOT (GPIO0)
SizeAbout 57 x 28mm, with the antenna end overhanging the pin rows. The pin rows are about 25mm apart, so it covers most of one breadboard
HeadersSoldered: straight pins fitted. Unsoldered: two loose 22-pin strips in the bag, 44 joints to solder. No USB-C cable included

Datasheets

Wiring & getting started

  1. Use a USB-C data cable

    A charge-only cable powers the board but no port ever appears, so if nothing shows up on your computer, swap the cable first. None is included. Most computers need a USB-A to USB-C data cable.

  2. Fit the pins (Unsoldered, optional)

    Push both strips into a breadboard with the long pins down, sit the board on top so every pin comes through its hole, and solder the 44 joints. The breadboard keeps the pins straight while you work. To wire it up afterwards, set two breadboards side by side and sit the board across both, which leaves free holes for jumper wires on each side.

  3. Pick a USB port

    Use the port marked COM for everyday uploads. It goes through a CH343P serial chip, so Windows may ask for the WCH CH343 driver the first time and then lists the board as a COM port. The port marked USB is the ESP32-S3's own USB, which you need for USB keyboard or mouse projects. Plug in one cable at a time while you are learning.

  4. Set up the Arduino IDE

    In Tools > Board > Boards Manager, search esp32 and install the esp32 package, version 3.x. Choose Tools > Board > esp32 > ESP32S3 Dev Module, then set Flash Size to 16MB (128Mb) and PSRAM to OPI PSRAM, because this module has octal PSRAM and the default setting leaves it off or stops the board starting. Pick a 16MB partition scheme if you want to use all the flash. If you upload over the COM port, leave USB CDC On Boot disabled and Serial Monitor works at 115200. If you upload over the USB port, set USB CDC On Boot to Enabled.

  5. Upload a first test

    This sketch prints the flash and PSRAM it finds. Arduino shows "Hash of data verified." when the upload has worked. Then open Serial Monitor at 115200.

    Example Arduino codeArduino C++
    // First test: report flash and PSRAM on the ESP32-S3-N16R8.
    void setup() {
      Serial.begin(115200);
      delay(2000);
    }
    
    void loop() {
      Serial.printf("Flash %u bytes, PSRAM %u bytes\n",
                    ESP.getFlashChipSize(), ESP.getPsramSize());
      delay(2000);
    }
  6. Check it works

    Serial Monitor repeats a flash size of 16777216 bytes and a PSRAM size of about 8 million bytes. If PSRAM shows 0, the PSRAM setting is not OPI PSRAM. If the board restarts over and over after you changed that setting, check Flash Size is 16MB. If the upload can't connect, hold BOOT, press and release RST, let go of BOOT and upload again. If Serial Monitor stays blank, you are on the other USB port from the one your USB CDC On Boot setting expects.

  7. Use the RGB LED (optional)

    The RGB LED is not connected to a pin as the board arrives, because the solder pad marked RGB beside it is open. If you want the LED, bridge that pad with a blob of solder and the LED data line goes to GPIO48. Drive it with rgbLedWrite(48, red, green, blue) from the esp32 package 3.x or a NeoPixel library, and not with digitalWrite. If you don't need the LED, leave the pad open and GPIO48 stays free as a normal pin.

  8. Wire your parts

    Power small sensors from a 3V3 pin and run every ground back to a GND pin. Keep GPIO35, 36 and 37 free. The 5Vin pin is an input: it takes 5V from a supply, and on our boards the pad marked IN-OUT beside it is open, so don't expect 5V to come out of that pin when you plug in USB. If you feed 5Vin from an outside supply, unplug both USB cables first.

Frequently Asked Questions

Answers to the questions buyers ask most.

What do I set in the Arduino IDE for this board?
Choose ESP32S3 Dev Module, then set Flash Size to 16MB (128Mb) and PSRAM to OPI PSRAM. This module has octal PSRAM, so the QSPI setting that suits smaller S3 boards won't work here. If the board restarts over and over after you change the PSRAM setting, check the flash size is 16MB too.
Why can't I use GPIO35, 36 or 37?
The octal PSRAM uses those three pins internally. They are labelled on the board because the same layout is used for other versions, but anything you connect to them can make the board crash or restart. Use another pin.
Which USB-C port should I use?
Use the one marked COM for everyday uploads and Serial Monitor. It goes through a CH343P serial chip, so Windows may ask for the WCH CH343 driver the first time. The port marked USB is the ESP32-S3's own USB, which you need for USB keyboard, mouse or MIDI projects, and for it you set USB CDC On Boot to Enabled in Arduino. Plug in one cable at a time while you are learning.
Why doesn't the RGB LED light up?
On our boards the solder pad marked RGB beside the LED is open, so the LED isn't connected to any pin. Bridge that pad with a blob of solder and the LED data line goes to GPIO48. Then use rgbLedWrite(48, red, green, blue) in the esp32 package 3.x, or a NeoPixel library, and not digitalWrite. If you don't need the LED, leave the pad open and GPIO48 stays free as a normal pin.
Can I power things from the 5V pin?
Treat the pin marked 5Vin as an input. On our boards the pad marked IN-OUT beside it is open, so 5V from USB is not sent out to that pin. For 5V parts, power them from their own supply, or measure the pin with a multimeter before you rely on it. Don't feed 5Vin from a supply while a USB cable is also plugged in.
Does it come with the pin headers soldered on?
Soldered has the pins fitted, ready for a breadboard. Unsoldered comes with two loose 22-pin strips in the bag, so you solder 44 joints yourself. If you have a soldering iron, Unsoldered is fine, and the breadboard holds the pins straight while you work.
How is this different from the 30-pin ESP32-WROOM-32 board?
This one has the newer ESP32-S3 chip, 16MB of flash, 8MB of PSRAM, native USB for keyboard and mouse projects, and Bluetooth 5 LE. It does not have Classic Bluetooth, which the original ESP32 has. For a simple WiFi sensor or relay project the 30-pin board is cheaper and does the job. Choose this one when you need the memory or the USB features.
Is this Espressif's own board?
No. It is a compatible board, with the same style of pin labels as Espressif's ESP32-S3-DevKitC-1, built around an ESP32-S3-N16R8 module. Your code carries over, but the board shape, USB ports and solder pads are different, so a shield made for Espressif's board may not fit.
Does it work with a camera or a screen?
The chip and memory suit both: the 8MB of PSRAM is what holds camera frames and screen images. This board has no camera or screen connector, so you wire a camera module or display to the pins yourself, and the pins you choose must avoid GPIO35, 36 and 37.

Have a Question About This Product?

Send it through and we will get back to you by email.

Why Buy from NZN

Useful parts, fair prices and someone local to help.

I'm Lukas, an engineering student and maker based in Te Awamutu. NZN grew out of a CNC build that dragged on for months because every missing cable, bolt or electronic part meant another overseas order. I started the shop so Kiwi makers can spend more time building and less time waiting for the next parcel.

  • Stocked here in New Zealand

    Orders are picked and packed in Te Awamutu and dispatched within 24 hours every day, excluding public holidays. NZ Post target delivery is 1-2 days urban and 2-4 days rural. In Te Awamutu and Kihikihi you can choose local delivery at checkout: same day if you order before 8am, otherwise next day.

  • Fair prices, clearly shown

    Prices are kept competitive and quantity discounts are shown upfront. Free delivery starts at $50 for urban addresses and $88 for rural addresses.

  • 30-day returns and 12-month warranty

    Get in touch if something is not right and we will help sort it.

  • Practical product support

    Ask a product question and get help from a real person in New Zealand who knows the range.

You may also like