530 piece heat shrink tubing kit in a clear 12 compartment box, lid open, red, yellow, blue, green and black tubes sorted by size

Heat Shrink Tubing Kit - 530pc, 2:1, 8 Sizes 1.5mm to 10mm, 5 Colours

$14.49 NZD
Skip to product information
SKU: HST-KIT-530

Heat Shrink Tubing Kit - 530pc, 2:1, 8 Sizes 1.5mm to 10mm, 5 Colours

$14.49 NZD
Availability:
Order before 7:30am (12pm weekends) for same-day dispatch Dispatch 7 days a week, excluding public holidays

NZ Post: 1-2 days urban · 2-4 days rural

Shipping from $5.99 urban / $9.99 rural, or free pick-up in Te Awamutu.

Easy 30-day returns · 12-month warranty

Add $50.00 for Free Urban delivery ($88.00 for Rural)
Urban $50 Rural $88

Heat shrink tubing is a plastic sleeve that tightens around a wire join when you heat it, so the bare metal is covered and the join is held firm. This kit has 530 pre-cut pieces of 2:1 polyolefin tube in eight sizes from 1.5mm to 10mm, sorted by size and colour in a 12-compartment box. 2:1 means a piece shrinks to about half the size on the label, so a 4mm piece ends up gripping anything thicker than 2mm.

It is made for low-voltage wiring such as Arduino projects and 12V vehicle looms. You can use it to insulate a soldered join in hook-up wire, cover a repair in a 12V loom, or colour-code the ends of a cable. Most of the pieces are the small sizes that electronics work goes through fastest: 240 of them are 1.5mm or 2mm, and there are 20 of each large size. The tube insulates a join but does not seal out water, so for a join that will get wet our Solder Seal connectors are the ones to use. It needs about 120°C to shrink fully, which a heat gun gives easily.

Specifications

Shrink ratio2:1, shrinks to about half its size
Sizes before shrinking1.5, 2, 3, 4, 5, 6, 8 and 10mm diameter
Piece length45mm, hand cut, give or take 2 to 3mm
Pieces530 in 12 compartments
ColoursBlack, red, yellow, blue, green
MaterialPolyolefin
Shrink temperatureStarts at about 84°C, fully shrunk at about 120°C
Working temperature-55°C to +125°C
Storage boxClear plastic, about 197 x 132 x 36mm

What's in the box

1×
Storage box with 530 pieces of heat shrink tube

Each size and colour has its own compartment, and the clear lid lets you see every size at a glance.

Size Shrinks to about Colour Pieces
1.5mm 0.75mm Yellow 80
2mm 1mm Blue 80
2mm 1mm Black 80
3mm 1.5mm Green 60
4mm 2mm Red 50
4mm 2mm Black 50
5mm 2.5mm Black 30
6mm 3mm Yellow 20
8mm 4mm Red 20
10mm 5mm Green 20
10mm 5mm Blue 20
10mm 5mm Black 20

Picking a size & getting started

  1. Measure the join and the wire

    The tube has to slide over the widest part of the join, and it has to finish tighter than the wire beside it. So the size you pick must be bigger than the join and less than twice the thickness of the wire, measured over its insulation.

  2. Pick the smallest size that slides on easily

    A join 3.5mm across in wire 2.5mm thick takes the 4mm tube, which shrinks to about 2mm and grips the wire. If two sizes fit, the smaller one ends up tighter.

  3. Slide it on before you make the join

    Push the piece down one wire, at least 3cm back from where you will solder, so the heat of the iron does not shrink it early. If the 45mm piece is longer than you need, cut it straight across with scissors and leave a few millimetres spare, because the tube gets a little shorter as it shrinks.

  4. Cover the join and heat it

    Once the join is cool, slide the piece over it so it overlaps the insulation on both sides. Heat it with a heat gun, starting in the middle and working out to each end, and keep the gun moving. If you only have a lighter, hold the tube just above the flame and keep it moving, because tube held in the flame scorches and picks up soot.

  5. Check it worked

    The tube should sit tight along its whole length, show the shape of the join underneath and stay put when you push it. If it still slides, it was too big for that wire, so cut it off and use the next size down.

Frequently Asked Questions

Answers to the questions buyers ask most.

Which size fits 22 AWG hook-up wire?
The 2mm tube. Our 22 AWG solid core hook-up wire is about 1.6mm across its insulation, so a 2mm piece slides over it and shrinks tight. A soldered join in that wire is fatter than the wire, so it needs the 3mm tube. That shrinks to about 1.5mm, which only just grips 1.6mm wire, so keep the join slim.
Why does a 4mm piece measure about 6mm across?
Because the pieces are packed flat. The size on the label is the round diameter before shrinking, and a flattened tube measures about one and a half times that. Squeeze the two edges together and it opens into a 4mm round tube.
The tube fits over my join but stays loose on the wire. What can I do?
That happens when the join is more than twice as thick as the wire, because 2:1 tube only shrinks to half its size. Shrink a short piece of a smaller size onto the wire on each side of the join first. Then shrink the larger piece over the top, so it grips those instead of the bare wire insulation.
Can I fit the tube over a plug that is already on the cable?
Only when the plug is narrower than the tube and the cable is thicker than half the tube's size. A 10mm piece passes over a plug up to about 9mm across and then needs a cable thicker than 5mm to grip. If your plug is wider than that, slide the piece onto the cable before you fit the plug.
Will a hair dryer shrink it?
Not properly. The tube needs about 120°C to shrink fully and most hair dryers do not get that hot, so it stays loose. A heat gun is the right tool.
Which sizes come in both red and black?
Only the 4mm size, with 50 pieces of each, so that is the one to use for marking positive and negative leads. Black also comes in 2mm, 5mm and 10mm, and red also comes in 8mm.

Have a Question About This Product?

Send it through and we will get back to you by email.

Why Buy from NZN

Useful parts, fair prices and someone local to help.

I'm Lukas, an engineering student and maker based in Te Awamutu. NZN grew out of a CNC build that dragged on for months because every missing cable, bolt or electronic part meant another overseas order. I started the shop so Kiwi makers can spend more time building and less time waiting for the next parcel.

  • Stocked here in New Zealand

    Orders are picked and packed in Te Awamutu and dispatched within 24 hours every day, excluding public holidays. NZ Post target delivery is 1-2 days urban and 2-4 days rural. In Te Awamutu and Kihikihi you can choose local delivery at checkout: same day if you order before 8am, otherwise next day.

  • Fair prices, clearly shown

    Prices are kept competitive and quantity discounts are shown upfront. Free delivery starts at $50 for urban addresses and $88 for rural addresses.

  • 30-day returns and 12-month warranty

    Get in touch if something is not right and we will help sort it.

  • Practical product support

    Ask a product question and get help from a real person in New Zealand who knows the range.

You may also like