Double-sided green prototype PCB, 4 x 6 cm, 14 by 20 plated through-holes on a 2.54 mm grid with oval edge pads, top view

Double-Sided Prototype PCB 4x6 or 5x7cm - 2.54mm Plated Through-Hole Perfboard

4 x 6 cm
$1.79 NZD
Save 5% at 3+
Skip to product information
SKU: PCB-PROTO-DS-4X6

Double-Sided Prototype PCB 4x6 or 5x7cm - 2.54mm Plated Through-Hole Perfboard

$1.79 NZD
Size
Availability:
Order before 7:30am (12pm weekends) for same-day dispatch Dispatch 7 days a week, excluding public holidays

NZ Post: 1-2 days urban · 2-4 days rural

Shipping from $5.99 urban / $9.99 rural, or free pick-up in Te Awamutu.

Buy more, pay less Prices shown are per unit. Add enough of this item and the lower rate applies on its own at checkout. There is no code to enter and you do not need to buy a pack. Choosing a tier here just sets the quantity for you. Larger quantities go out in the same bag, so packing, handling and postage cost us less per unit. We pass that saving straight on to you, so you can buy more for less.

Easy 30-day returns · 12-month warranty

Add these too
Add $50.00 for Free Urban delivery ($88.00 for Rural)
Urban $50 Rural $88

A double-sided prototype PCB, also called perfboard, for turning a breadboard circuit into something permanent. The holes sit on a 2.54 mm grid, so pin headers, chip sockets and modules such as an ESP32 or Nano drop straight in. Every hole is plated through and has a tinned pad on both sides, so you can solder from either side and the joints hold well.

This isn't stripboard. The pads aren't joined, so you make each connection with a short wire or a solder bridge between pads. Pick 4 x 6 cm for a sensor and a small board like an ESP32-C3 SuperMini, or 5 x 7 cm when you need room for a Nano and a few more parts. Use them for sensor shields, LED and button panels, small power circuits and anything you want to keep off the breadboard.

Specifications

Sizes4 x 6 cm or 5 x 7 cm, choose above
Holes4 x 6 cm: 14 x 20 (280). 5 x 7 cm: 18 x 24 (432)
Hole pitch2.54 mm (0.1 inch), the same as breadboards, pin headers and DIP chips
PadsRound tinned pads on both sides, every hole plated through
Between padsNo connections. Every pad is separate, so you join them with wire or solder
Edge padsA row of long oval pads along each short edge, handy for wires and power
Hole sizeAbout 1 mm. Fits header pins and most through-hole leads
BoardGreen fibreglass (FR4 type), about 1.6 mm thick, four corner mounting holes
Grid markingsNumbers and letters printed along the edges, so you can find each hole

Wiring & getting started

  1. Plan the layout

    Put your parts on the board before you solder anything, and use the printed numbers and letters to note where each one goes. Parts go on the top and the joining wires usually go underneath.

  2. Solder with moderate heat

    Around 330 to 350°C for two or three seconds a joint is plenty. The plated holes pull solder through to the other side, which is normal. Too much heat, or reworking the same joint again and again, can lift a pad off the board.

  3. Join the pads

    For pads next to each other, bend a lead over or run a blob of solder across. For longer runs, solder a length of 22 AWG solid hook-up wire along the back. Use the oval edge pads for power, ground or wires going off the board.

  4. Clean and check

    Wipe the flux off with isopropyl alcohol and a small brush. Then look between neighbouring pads for any solder that has bridged by accident, and check the power and ground for a short with a meter before you plug anything in.

Frequently Asked Questions

Answers to the questions buyers ask most.

Is this stripboard or perfboard?
Perfboard. Every pad is separate, so nothing is joined until you solder it. Join pads with a short wire, a bent-over lead or a solder bridge. Stripboard has copper strips that join a whole row, which you then cut where you don't want a connection.
Which size should I get?
The 4 x 6 cm board suits a small circuit: a sensor or two, a few LEDs and buttons, or a small board such as an ESP32-C3 SuperMini. The 5 x 7 cm board has 432 holes against 280, which leaves room for a Nano or ESP32 with its supporting parts. If you're unsure, the bigger board is easier to lay out, and you can cut off what you don't use.
Can I cut the board to size?
Yes. Score along a row of holes on both sides with a sharp craft knife and a steel ruler, then snap it over the edge of a table. Sand the cut edge smooth. Cut through holes you don't need, not through pads you've used.
Will pin headers and IC sockets fit?
Yes. The 2.54 mm grid matches standard pin headers, female headers, DIP chips and their sockets. The holes are about 1 mm, which suits most through-hole parts. Very thick leads, such as some large diodes or screw terminal pins, may need that hole drilled out a little.
Why does double-sided with plated holes matter?
Solder flows through the hole and grips both sides, so joints are stronger and pads are less likely to tear off than on a single-sided board. You can also solder parts or wires on either face. The catch is that a part is harder to remove, so use solder wick from both sides when you need to take one out.
Can I mount the board in a case?
Yes. There's a mounting hole in each corner, so you can screw the board to a case or lid on standoffs. Keep solder joints and wires a few millimetres away from metal screw heads.

Have a Question About This Product?

Send it through and we will get back to you by email.

Why Buy from NZN

Useful parts, fair prices and someone local to help.

I'm Lukas, an engineering student and maker based in Te Awamutu. NZN grew out of a CNC build that dragged on for months because every missing cable, bolt or electronic part meant another overseas order. I started the shop so Kiwi makers can spend more time building and less time waiting for the next parcel.

  • Stocked here in New Zealand

    Orders are picked and packed in Te Awamutu and dispatched within 24 hours every day, excluding public holidays. NZ Post target delivery is 1-2 days urban and 2-4 days rural. In Te Awamutu and Kihikihi you can choose local delivery at checkout: same day if you order before 8am, otherwise next day.

  • Fair prices, clearly shown

    Prices are kept competitive and quantity discounts are shown upfront. Free delivery starts at $50 for urban addresses and $88 for rural addresses.

  • 30-day returns and 12-month warranty

    Get in touch if something is not right and we will help sort it.

  • Practical product support

    Ask a product question and get help from a real person in New Zealand who knows the range.

You may also like