Passive buzzer module with low level trigger, black buzzer on a blue board with 3 right-angle header pins marked VCC, I/O and GND

Passive Buzzer Module for Arduino, Low Level Trigger, 3.3 to 5V

$1.59 NZD
Save 5% at 3+
Skip to product information
SKU: MOD-BUZ-PAS-L

Passive Buzzer Module for Arduino, Low Level Trigger, 3.3 to 5V

$1.59 NZD
Availability:
Order before 7:30am (12pm weekends) for same-day dispatch Dispatch 7 days a week, excluding public holidays

NZ Post: 1-2 days urban · 2-4 days rural

Shipping from $5.99 urban / $9.99 rural, or free pick-up in Te Awamutu.

Buy more, pay less Prices shown are per unit. Add enough of this item and the lower rate applies on its own at checkout. There is no code to enter and you do not need to buy a pack. Choosing a tier here just sets the quantity for you. Larger quantities go out in the same bag, so packing, handling and postage cost us less per unit. We pass that saving straight on to you, so you can buy more for less.

Easy 30-day returns · 12-month warranty

Add these too
Add $50.00 for Free Urban delivery ($88.00 for Rural)
Urban $50 Rural $88

A small buzzer board that plays notes. It has no oscillator of its own, so your code supplies the pitch: tone() on an Arduino, PWM on an ESP32 or Pico. That makes it the one to pick for start-up jingles, simple tunes, rising alarms and different beeps for different events. A transistor on the board does the switching, so your pin only supplies a few milliamps.

Passive and active buzzers look alike, and the difference matters. A passive buzzer stays silent on a plain HIGH or LOW and only clicks, because it needs a switching signal. An active buzzer beeps by itself when you switch it on, with one fixed tone. If you only want a fixed beep from digitalWrite, get our Active Buzzer Module instead. This board is the Low level type: leave I/O HIGH when idle, and on a 3.3V board such as an ESP32 or Pico, power VCC from 3.3V, not 5V.

Specifications

BuzzerPassive buzzer, about 12 mm across, no built-in oscillator
Drive signalA square wave from tone() or PWM; a steady HIGH or LOW only clicks
TriggerLow level: keep I/O HIGH when idle, it sounds while the pin switches
Supply3.3 to 5V DC on VCC
Logic3.3V or 5V. On an ESP32 or Pico, run VCC from 3.3V
DriverTransistor with a 1k base resistor, so one pin is all it needs
PinsVCC, I/O, GND on a right-angle 3-pin header (2.54 mm)
Board size32.2 x 13.1 mm, one mounting hole that takes an M3 screw
SoundAny note you can generate, one at a time, at small-beeper volume

Datasheets

Wiring & getting started

Wiring diagramArduino Uno
Passive buzzer module wired to an Arduino Uno: VCC to 5V, I/O to D8, GND to GND
Tap the drawing to open it full size.
  1. Connect three wires

    The pin names are printed beside the header. VCC goes to 5V, I/O to D8 and GND to GND. On an ESP32 or Pico, use 3.3V for VCC. Three female jumper wires push straight onto the pins.

  2. Load the test code

    Upload this sketch to an Uno. It plays eight notes, then sets the pin back to HIGH, which is the quiet level for this board.

    Example Arduino codeArduino C++
    // Passive buzzer module test (MOD-BUZ-PAS-L, Low level trigger).
    // Module VCC to 5V, I/O to D8, GND to GND on the Uno.
    // The board is silent while the pin is HIGH, so HIGH is the idle level.
    const int BUZ = 8;
    const int NOTES[] = {262, 294, 330, 349, 392, 440, 494, 523};  // C4 up to C5
    
    void playNote(int hz, int ms) {
      tone(BUZ, hz, ms);
      delay(ms + 20);
      digitalWrite(BUZ, HIGH);  // tone() leaves the pin LOW, so put it back to idle
    }
    
    void setup() {
      digitalWrite(BUZ, HIGH);  // set the idle level first
      pinMode(BUZ, OUTPUT);     // so it stays quiet at start
    }
    
    void loop() {
      for (int i = 0; i < 8; i++) {
        playNote(NOTES[i], 300);
      }
      delay(2000);
    }
  3. Check it works

    You should hear a rising scale from C to C, then two seconds of quiet, repeating. If you only hear clicks, the code is switching the pin on and off with digitalWrite instead of calling tone(). Change the numbers in NOTES to play your own tune.

Frequently Asked Questions

Answers to the questions buyers ask most.

What is the difference between this and the Active Buzzer Module?
An active buzzer has its own oscillator and beeps at one fixed tone whenever it's switched on, so digitalWrite is enough. A passive buzzer like this one has no oscillator and needs your code to supply the tone, which lets you choose the pitch and play simple tunes. Powered from DC with no switching signal, a passive buzzer only clicks.
Why do I only hear a click?
A passive buzzer needs a switching signal, so digitalWrite(HIGH) or LOW gives one click and then silence. Use tone(pin, frequency) on an Arduino, which switches the pin for you. Notes from about 2 to 5 kHz come out clearest and loudest, and very low notes come out quiet and thin.
Will it work with an ESP32, Pico or other 3.3V board?
Yes. Power VCC from 3.3V on a 3.3V board. With VCC on 5V, a 3.3V HIGH can't switch this Low level board fully off. On an ESP32, tone() works in the current Arduino core (3.x); older cores use ledcWriteTone() instead. On a Pico, use PWM or the Arduino-Pico tone() function.
Why does it hum or get warm when it's meant to be quiet?
This board is Low level, so a steady LOW passes steady current through the buzzer without making a tune. Arduino's tone() leaves the pin LOW when a note ends, so call digitalWrite(pin, HIGH) after each note, as the example sketch does. A pin that floats while your board starts up can do the same until your code sets it HIGH.
Can I use tone() and analogWrite together?
On an Arduino Uno, tone() uses Timer2, which stops analogWrite working on pins 3 and 11 while a note plays. Put the buzzer on another pin, such as D8, and keep PWM outputs on pins 5, 6, 9 and 10. Only one note plays at a time, and you need noTone() before moving tone() to a different pin.
How loud is it, and can it play music?
It's a small buzzer, loud enough for alarms and button feedback, not for music or speech. It plays one note at a time, which is fine for simple tunes. For audio files or voice, use a speaker with an amplifier such as our SC8002B module.

Have a Question About This Product?

Send it through and we will get back to you by email.

Why Buy from NZN

Useful parts, fair prices and someone local to help.

I'm Lukas, an engineering student and maker based in Te Awamutu. NZN grew out of a CNC build that dragged on for months because every missing cable, bolt or electronic part meant another overseas order. I started the shop so Kiwi makers can spend more time building and less time waiting for the next parcel.

  • Stocked here in New Zealand

    Orders are picked and packed in Te Awamutu and dispatched within 24 hours every day, excluding public holidays. NZ Post target delivery is 1-2 days urban and 2-4 days rural. In Te Awamutu and Kihikihi you can choose local delivery at checkout: same day if you order before 8am, otherwise next day.

  • Fair prices, clearly shown

    Prices are kept competitive and quantity discounts are shown upfront. Free delivery starts at $50 for urban addresses and $88 for rural addresses.

  • 30-day returns and 12-month warranty

    Get in touch if something is not right and we will help sort it.

  • Practical product support

    Ask a product question and get help from a real person in New Zealand who knows the range.

You may also like