Black MB102 breadboard power module with USB-A socket, barrel jack and push switch

MB102 Breadboard Power Supply Module 3.3V/5V - DC Jack & USB-A, Black

$3.69 NZD
Save 5% at 3+
Skip to product information
SKU: PWR-MB102-BLK

MB102 Breadboard Power Supply Module 3.3V/5V - DC Jack & USB-A, Black

$3.69 NZD
Availability:
Order before 7:30am (12pm weekends) for same-day dispatch Dispatch 7 days a week, excluding public holidays

NZ Post: 1-2 days urban · 2-4 days rural

Shipping from $5.99 urban / $9.99 rural, or free pick-up in Te Awamutu.

Buy more, pay less Prices shown are per unit. Add enough of this item and the lower rate applies on its own at checkout. There is no code to enter and you do not need to buy a pack. Choosing a tier here just sets the quantity for you. Larger quantities go out in the same bag, so packing, handling and postage cost us less per unit. We pass that saving straight on to you, so you can buy more for less.

Easy 30-day returns · 12-month warranty

Add these too
Add $50.00 for Free Urban delivery ($88.00 for Rural)
Urban $50 Rural $88

A plug-in power supply for a solderless breadboard. It sits across one end of an MB-102 style breadboard, pushes into both power rails and turns a 7 to 10V DC plug pack into a steady 5V or 3.3V on each rail. Each side has its own jumper, so one rail can run a 5V Arduino sensor while the other runs a 3.3V part such as an ESP32 module.

This black version has a push on/off button, a green power light and a USB-A socket. From the barrel jack you can plan on about 400mA across both rails from a 7.5V plug pack, enough for sensors, LEDs and a small display but not motors or servos. If you would rather power your breadboard from a USB cable, the white MB102 module has a mini USB input, no button, and a notched shape that leaves the breadboard rows under it free. The blue MB102 module also takes mini USB, on a narrower board with jumpers like this one and no button.

Specifications

DC input7 to 10V, 5.5 x 2.1mm plug, centre positive
Best supply7.5 to 9V plug pack
Outputs5V or 3.3V per rail, jumper set (5V / OFF / 3.3V)
Current (NZN limit)About 400mA at 7.5V in, 250mA at 9V, 200mA at 10V, both rails together
USB-A socket5V, wired to the 5V rail (see FAQs)
Extra outputsHeader with 2 x 3.3V, 2 x 5V and 4 x GND pins
ControlsPush on/off button, green power light
FitsMB-102 style 830 and 400 point breadboards
SizeAbout 53 x 33mm, 12g

Datasheets

Wiring & getting started

  1. Line up + with the red line

    Each end of the module has a + row and a - row of pins, marked on the board. Turn the module so both + rows sit over the red lines of the breadboard, then press it straight down. On our 830 point and 400 point breadboards that one direction gets both sides right. Turned the other way round, both rails come out reversed.

  2. Set each rail's jumper

    The yellow jumper beside each end picks 5V, OFF or 3.3V for that rail, as marked next to it. Jumpers can arrive in any position, so set both before you plug in. A 3.3V part such as a BMP280 or an ESP32 module can be damaged on a 5V rail.

  3. Plug in and press the button

    Use a 7.5 to 9V plug pack with a 5.5 x 2.1mm centre-positive plug, or a battery through our barrel jack screw terminal adapter. Press the white button and the green light comes on.

  4. Measure before you connect

    Check each rail with a multimeter: 4.9 to 5.1V and 3.2 to 3.4V are normal. A rail reading close to your plug pack voltage means its jumper isn't fully pushed on, so switch off and reseat it.

  5. Wire your circuit

    Run jumper wires from the rails to your parts. Give motors, servos and LED strips their own supply, because their start-up current is more than this module gives.

Frequently Asked Questions

Answers to the questions buyers ask most.

Is the USB-A socket an input or an output?
It can be either, because it is wired straight to the 5V rail. With a plug pack in the barrel jack and the button on, it gives out 5V, so you can run a small USB gadget such as a USB light, counted in the current limit. It can also take power in from a computer or USB charger through a USB A-to-A cable (male plug at both ends, not included), which feeds the 5V rail directly. The button switches it either way. Never connect the barrel jack and USB power at the same time. If USB will be your main power source, the white MB102 module with its mini USB input is the simpler choice.
Can I use a 12V plug pack?
We don't recommend it. The board is marked 7-10V, and the regulators turn the extra voltage into heat, so at 12V they reach their heat limit at only about 150mA. A 7.5V or 9V plug pack is a better fit.
Why does a rail cut out and come back on?
The regulator is getting too hot and shutting itself down until it cools. Your circuit is drawing more than the module can give at that input voltage. Use a lower voltage plug pack (7.5V is best) or move the hungry part, such as a motor or a strip of LEDs, to its own supply. The 3.3V rail's current counts towards the total too.
Can I power an Arduino Uno or Nano from it?
Yes. Set a rail to 5V and run a jumper from it to the Arduino's 5V pin, and another from the - rail to GND. Unplug the Arduino's USB cable while you do this so two supplies aren't connected at once. An Uno with a few sensors draws well under the module's limit.
Will it fit my breadboard?
It fits MB-102 style 830 and 400 point breadboards with a pair of power rails down each side, like ours. It doesn't suit a mini 170 point breadboard, which has no power rails. Breadboards from other makers sometimes space the rails differently or swap the red and blue lines on one side, so check that both + rows land on red lines before you power up.
How do I switch one rail off?
Move that rail's jumper to the OFF position marked beside it. The other rail keeps running, which is handy when you want to wire up one side of the board while the other side stays powered.

Have a Question About This Product?

Send it through and we will get back to you by email.

Why Buy from NZN

Useful parts, fair prices and someone local to help.

I'm Lukas, an engineering student and maker based in Te Awamutu. NZN grew out of a CNC build that dragged on for months because every missing cable, bolt or electronic part meant another overseas order. I started the shop so Kiwi makers can spend more time building and less time waiting for the next parcel.

  • Stocked here in New Zealand

    Orders are picked and packed in Te Awamutu and dispatched within 24 hours every day, excluding public holidays. NZ Post target delivery is 1-2 days urban and 2-4 days rural. In Te Awamutu and Kihikihi you can choose local delivery at checkout: same day if you order before 8am, otherwise next day.

  • Fair prices, clearly shown

    Prices are kept competitive and quantity discounts are shown upfront. Free delivery starts at $50 for urban addresses and $88 for rural addresses.

  • 30-day returns and 12-month warranty

    Get in touch if something is not right and we will help sort it.

  • Practical product support

    Ask a product question and get help from a real person in New Zealand who knows the range.

You may also like