Blue MB102 breadboard power supply module top view with DC jack, mini USB socket, a 3.3V or 5V jumper for each rail and the 2x3 rail pins at each end

MB102 Breadboard Power Supply Module 3.3V/5V - Mini USB & Jumpers, Blue

$3.69 NZD
Save 5% at 3+
Skip to product information
SKU: PWR-MB102-BLU

MB102 Breadboard Power Supply Module 3.3V/5V - Mini USB & Jumpers, Blue

$3.69 NZD
Availability:
Order before 7:30am (12pm weekends) for same-day dispatch Dispatch 7 days a week, excluding public holidays

NZ Post: 1-2 days urban · 2-4 days rural

Shipping from $5.99 urban / $9.99 rural, or free pick-up in Te Awamutu.

Buy more, pay less Prices shown are per unit. Add enough of this item and the lower rate applies on its own at checkout. There is no code to enter and you do not need to buy a pack. Choosing a tier here just sets the quantity for you. Larger quantities go out in the same bag, so packing, handling and postage cost us less per unit. We pass that saving straight on to you, so you can buy more for less.

Easy 30-day returns · 12-month warranty

Add these too
Add $50.00 for Free Urban delivery ($88.00 for Rural)
Urban $50 Rural $88

A plug-in power supply for a solderless breadboard that runs from a USB cable or a DC plug pack. It sits across one end of an MB-102 style breadboard, pushes into both power rails and gives a steady 5V or 3.3V on each rail. A jumper beside each output sets that rail, so one side can run a 5V Arduino sensor while the other runs a 3.3V part such as an ESP32 module. Pull a jumper off and that rail goes dead while the other keeps running.

This blue version is a narrow strip with a mini USB input and a DC jack marked 7-12V. It has no on/off switch, so it's on whenever it's plugged in. For anything more than a few sensors, use a 7.5 to 9V plug pack: the regulators turn the extra voltage into heat, so from 12V you only get about 140mA. On USB power, plan on about 500mA across both rails. The white MB102 module has the same two inputs with slide switches instead of jumpers, and the black MB102 module runs from a plug pack only, with a push on/off button and a USB-A socket.

Specifications

USB input5V through a mini USB socket (cable not included)
DC input7 to 12V as marked, 5.5 x 2.1mm plug, centre positive
Best supply7.5 to 9V plug pack
Outputs5V or 3.3V per rail, set by jumper, or off with the jumper removed
Current (NZN limit)From DC: about 400mA at 7.5V in, 250mA at 9V, 140mA at 12V, both rails together
USB currentPlan on about 500mA, what a computer USB port gives
IndicatorPower light, no on/off switch
FitsMB-102 style 830 and 400 point breadboards
SizeAbout 56 x 23mm plus the jack, 6g

Datasheets

Wiring & getting started

  1. Line up OUT with the red line

    Each end of the module has two rows of three pins, marked OUT and GND on the board. Turn the module so both OUT rows sit over the red (+) lines of the breadboard and both GND rows over the blue (-) lines, then press it straight down. On our 830 point and 400 point breadboards that one direction gets both sides right. Turned the other way round, both rails come out reversed.

  2. Set each rail's jumper

    Each output has a small 3-pin header marked 3.3, OUT and 5V. The jumper joins the middle OUT pin to the voltage you want. Ours can arrive set to 3.3V or 5V, so check both before you plug in. A 3.3V part such as a BMP280 or an ESP32 module can be damaged on a 5V rail. Pull a jumper off and that rail is switched off.

  3. Plug in one power source

    Use a mini USB cable (the older, wider plug, not micro USB or USB-C) from a computer or phone charger, or a 7.5 to 9V plug pack with a 5.5 x 2.1mm centre-positive plug. The power light comes on straight away. Use one source at a time, never both.

  4. Measure before you connect

    Check each rail with a multimeter: 4.9 to 5.1V and 3.2 to 3.4V are normal on a plug pack. A rail that reads nothing or wanders means its jumper isn't pushed fully on, so unplug and reseat it.

  5. Wire your circuit

    There are no separate output pins on this board, so run jumper wires from the breadboard rails to your parts. Give motors, servos and LED strips their own supply, because their start-up current is more than this module gives.

Frequently Asked Questions

Answers to the questions buyers ask most.

What USB cable do I need?
A mini USB cable, the older, wider USB plug used on some cameras and older Arduino boards. Micro USB and USB-C plugs don't fit. The other end goes into a computer USB port or a USB phone charger. The cable isn't included.
Can I use a 12V plug pack?
It's within the 7-12V marked on the board, so it won't harm it, but the regulators turn the extra voltage into heat and reach their limit at only about 140mA from 12V. That's fine for a few LEDs and a sensor. A 7.5V or 9V plug pack gives you far more current to work with.
Why does a rail cut out and come back on?
The regulator is getting too hot and shutting itself down until it cools. Your circuit is drawing more than the module can give at that input voltage. Use a lower voltage plug pack (7.5V is best) or move the hungry part, such as a motor or a strip of LEDs, to its own supply. The 3.3V rail's current counts towards the total too.
How do I turn it off?
Unplug it. There's no on/off switch. To turn just one rail off, pull its jumper off and the other rail keeps running, which is handy when you're rewiring one side of the breadboard. Keep the loose jumper somewhere safe, as they're small and easy to lose.
Will it fit my breadboard?
It fits MB-102 style 830 and 400 point breadboards with a pair of power rails down each side, like ours. It doesn't suit a mini 170 point breadboard, which has no power rails. Breadboards from other makers sometimes space the rails differently or swap the red and blue lines on one side, so check that both OUT rows land on red lines before you power up.
Can I power an Arduino Uno or Nano from it?
Yes. Set a rail to 5V and run a jumper wire from it to the Arduino's 5V pin, and another from the blue (-) rail to GND. Unplug the Arduino's own USB cable while you do this so two supplies aren't connected at once.
Which MB102 module should I pick: blue, white or black?
Blue and white both take mini USB or a DC plug pack and have no power button. Blue uses jumpers, so you can switch a rail off, and it's the narrowest of the three. White uses slide switches that are quicker to change but have no off position. Black runs from a plug pack and adds a push on/off button and a USB-A socket.

Have a Question About This Product?

Send it through and we will get back to you by email.

Why Buy from NZN

Useful parts, fair prices and someone local to help.

I'm Lukas, an engineering student and maker based in Te Awamutu. NZN grew out of a CNC build that dragged on for months because every missing cable, bolt or electronic part meant another overseas order. I started the shop so Kiwi makers can spend more time building and less time waiting for the next parcel.

  • Stocked here in New Zealand

    Orders are picked and packed in Te Awamutu and dispatched within 24 hours every day, excluding public holidays. NZ Post target delivery is 1-2 days urban and 2-4 days rural. In Te Awamutu and Kihikihi you can choose local delivery at checkout: same day if you order before 8am, otherwise next day.

  • Fair prices, clearly shown

    Prices are kept competitive and quantity discounts are shown upfront. Free delivery starts at $50 for urban addresses and $88 for rural addresses.

  • 30-day returns and 12-month warranty

    Get in touch if something is not right and we will help sort it.

  • Practical product support

    Ask a product question and get help from a real person in New Zealand who knows the range.

You may also like