White MB102 breadboard power module with mini-USB, barrel jack and two slide switches

MB102 Breadboard Power Supply Module 3.3V/5V - Mini USB, White

$3.69 NZD
Save 5% at 3+
Skip to product information
SKU: PWR-MB102-WHT

MB102 Breadboard Power Supply Module 3.3V/5V - Mini USB, White

$3.69 NZD
Buy more, pay less Prices shown are per unit. Add enough of this item and the lower rate applies on its own at checkout. There is no code to enter and you do not need to buy a pack. Choosing a tier here just sets the quantity for you. Larger quantities go out in the same bag, so packing, handling and postage cost us less per unit. We pass that saving straight on to you, so you can buy more for less.

Easy 30-day returns · 12-month warranty

Availability:
Order before 7:30am (12pm weekends) for same-day dispatch
Delivery $5.99 urban, free from $50

NZ Post 1-2 days urban, 2-4 days rural

Rural delivery and pick-up
  • Urban delivery from $5.99, free on orders from $50.
  • Rural delivery from $9.99, free on orders from $88.
  • Free pick-up in Te Awamutu.
  • We dispatch every day except public holidays.
Shipping policy

A plug-in power supply for a solderless breadboard that runs from a USB cable or a DC plug pack. It sits across one end of an MB-102 style breadboard, pushes into both power rails and gives a steady 5V or 3.3V on each rail. A slide switch on each side sets that rail, so one side can run a 5V Arduino sensor while the other runs a 3.3V part such as an ESP32 module.

This white version has a mini USB input as well as the DC jack, and its notched shape leaves the breadboard rows under the middle of it free. It has no on/off switch, so it's on whenever it's plugged in. On USB power, plan on up to about 500mA across both rails: that's what a computer USB port gives, and the board's resettable fuse is sized for about the same. If you want an on/off button and a USB-A socket instead, the black MB102 module has both. The blue MB102 module has the same two inputs on a narrower board, with jumpers that can also switch a rail off.

Specifications

USB input5V through a mini USB socket (cable not included)
DC input7 to 10V, 5.5 x 2.1mm plug, centre positive
Outputs5V or 3.3V per rail, slide switch set (no off position)
Current (NZN limit)From DC: about 400mA at 7.5V in, 250mA at 9V, 200mA at 10V, both rails together
USB currentAbout 500mA, with a resettable fuse on the USB side
Extra outputs3 x 5V and 3 x 3.3V header pins, each with a GND pin
IndicatorPower light, no on/off switch
FitsMB-102 style 830 and 400 point breadboards
SizeAbout 53 x 30mm plus the jack, 10g

Datasheets

Wiring & getting started

  1. Line up + with the red line

    Each end of the module has a + row and a - row of pins, marked on the board. Turn the module so both + rows sit over the red lines of the breadboard, then press it straight down. On our 830 point and 400 point breadboards that one direction gets both sides right. Turned the other way round, both rails come out reversed.

  2. Set each rail's switch

    Slide the switch at each end to 3V3 or 5V, as marked beside it, before you plug in. A 3.3V part such as a BMP280 or an ESP32 module can be damaged on a 5V rail.

  3. Plug in one power source

    Use a mini USB cable (the older, wider plug, not micro USB or USB-C) from a computer or phone charger, or a 7.5 to 9V plug pack with a 5.5 x 2.1mm centre-positive plug. The power light comes on straight away. Use one source at a time, never both.

  4. Measure before you connect

    Check each rail with a multimeter: 4.9 to 5.1V and 3.2 to 3.4V are normal. A rail reading close to your plug pack voltage means its switch is caught between positions, so slide it fully across.

  5. Wire your circuit

    Run jumper wires from the rails or the header pins to your parts. Give motors, servos and LED strips their own supply, because their start-up current is more than this module gives.

Frequently asked questions

What USB cable do I need?
A mini USB cable, the older, wider USB plug used on some cameras and older Arduino boards. Micro USB and USB-C plugs don't fit. The other end goes into a computer USB port or a USB phone charger. The cable isn't included.
How much current can I draw on USB power?
Plan on about 500mA across both rails. That's what a computer USB port gives, and the resettable fuse beside the USB socket is sized for about the same, so a bigger phone charger won't give you much more. If you short a rail, the fuse cuts the USB power and resets once you remove the fault. The 3.3V rail's current comes out of the same total.
Can I use a 12V plug pack?
We don't recommend it. The board is marked DC 7-10V, and the regulators turn the extra voltage into heat, so at 12V they reach their heat limit at only about 150mA. A 9V plug pack, or USB power, is a better fit.
How do I turn it off?
Unplug it. This module has no on/off switch and the rail switches only choose between 3.3V and 5V, so a rail can't be turned off on its own. If you want a power button and an OFF position on each rail, the black MB102 module has both.
Will it fit my breadboard?
It fits MB-102 style 830 and 400 point breadboards with a pair of power rails down each side, like ours. It doesn't suit a mini 170 point breadboard, which has no power rails. Breadboards from other makers sometimes space the rails differently or swap the red and blue lines on one side, so check that both + rows land on red lines before you power up.
Can I power an Arduino Uno or Nano from it?
Yes. Set a rail to 5V and run a jumper from it to the Arduino's 5V pin, and another from the - rail to GND. Unplug the Arduino's own USB cable while you do this so two supplies aren't connected at once.

Have a question about this product?

Send it through and we will get back to you by email.

About NZN

Useful parts, fair prices and someone local to help.

I'm Lukas, an engineering student and maker based in Te Awamutu. NZN grew out of a CNC build that dragged on for months because every missing cable, bolt or electronic part meant another overseas order. I started the shop so Kiwi makers can spend more time building and less time waiting for the next parcel.

  • Stocked here in New Zealand

    Stock is held here in New Zealand, and every order is dispatched by the next day, except on public holidays. The timer beside Add to cart shows when yours goes out. NZ Post aims for 1-2 days urban and 2-4 days rural. In Te Awamutu and Kihikihi you can choose local delivery at checkout: same day if you order before 8am, otherwise next day.

  • Fair prices, clearly shown

    Where a product has quantity pricing, the price for each quantity is listed above Add to cart. Free delivery starts at $50 for urban addresses and $88 for rural addresses.

  • 30-day returns and 12-month warranty

    Get in touch if something is not right and we will help sort it.

  • Practical product support

    Ask a product question and get help from a real person in New Zealand who knows the range.

You may also like